Dukane 9100HC manual Connecting to Devices,  Connecting to Video Devices, Right side of projector

Page 21

Connecting to Various Devices

Connecting to Devices

Before connection, be sure to turn off both the projector and the device.

Connecting to Video Devices

•Thoroughly read the manual that comes with each video device.

•Use the supplied AV connection cable. S-video (Y/C) cable, BNC cable and PC Audio cables are not supplied.

Right side of projector

BNC Cable (sold separately)

R PR/CR

G Y

B PB/CB

H/CS

V

 

 

DVI

 

 

 

 

 

PC1

 

PC3

 

 

PC2

 

 

 

 

SCREEN

 

REMOTE

RS-232C OUT

RS-232C IN

Y/C

VIDEO

TRIGGER

AUDIO IN

 

 

CONTROL

 

VIDEO IN

PC Audio cable

S-video cable

(sold separately)

(sold separately)

AV connection cable (supplied)

Video Device 1

VCR (Video cassette recorder)

Video Device 2

DVD player

D-VHS or DVD player etc.

Camcorder

Image input

•Connect a composite image signal output device or Y/C (S-video) image output device.

Sound input

• Connect to [AUDIO IN] terminal.

Image input

•Connect to component signal output device, DTV format signal output device, etc.

•When the [PC2] input terminal is used, the “PC2(BNC)” item in “Options” menu must

be correctly set. (☞ page 39)

Sound input

• Connect to [AUDIO IN] terminal.

Connection

•When connecting a video device, please use a TBC along with it, or use one with a built-in TBC.

•Use of an extension cable to connect a video device and the projector could cause image deterioration or projection failure.

•When a signal with much jitter is reproduced on a VCR, or special-effect playbacks are performed, the upper part of the image or the screen may be interrupted, erased or distorted.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents
Model 9100HC Machine Noise Information Germany only FCC Information U.S.A. onlyDo not allow any unqualified person to install the unit Safety PrecautionPower supply voltage AC 120 For United For European KingdomDo not cut off the main plug from this equipment How To Replace The FuseHow to use the Screen Trigger terminal cable Using the projectorUsing the screen mode switch function About burning-in of the D-ILA deviceAccessories ContentsFront Side/ Top Surface/ Left Side Controls and FeaturesRear Side/ Right Side/ Bottom Surface Controls and FeaturesConnector Panel Control Panel on the Projector Indicator Display on the Control PanelOperate Indicator Stand by IndicatorLamp Indicator Temp IndicatorVolume button Remote Control UnitVideo button PC button Focus button Not functional on this unitVolume ª / · button Remote Control’s signal transmitter Operate buttonScreen „ / Í button Digital Zoom ª / · buttonsPrecautions for using batteries Loading Batteries into the Remote ControlOpen the back cover Load the batteriesPrecautions for Installation Installing the ProjectorInstalling the Projector Installing the Projector against the ScreenPrecaution for ceiling-mount Mounting the Projector Screen installation Projection Distance and Screen Size 43 Screen  Using as a wireless remote control unit Effective Range and Distance of the Remote Control Unit Using as a wired Remote Control When the remote control unit fails to work properlySignals that can be input into the projector Connecting to Various Devices Video signals  Computer signals Allowable input signals Connecting to Various Devices Connecting to Video Devices Connecting to DevicesRight side of projector Connection Connecting to Computers Connection for controlling more than one projector  Control from external device When using the projector, remove the Lens Cap Connecting the Power Cord suppliedPower On Basic Operation ProceduresInsert the power cord into the wall outlet Basic OperationsAdjusting the Zoom Ring the screen size  Display using the direct buttonsAdjusting the Focus Ring Focus Basic OperationsPower Off Adjusting the Sound VolumePress Volume · 50 Plug out the power cord from wall outletEnlarging the Image Frequently used Convenient FunctionsDisplaying a Still Picture Turning Off Image and SoundRemoving the Trapezoidal Distortion of the Image  Vert.keystone Display Horiz.Keystone Display Using the Quick Alignment function Press the Quick ALIGN. Quick Alignment buttonQuick Alignment function Menu Structure Adjustments and Settings Using MenusMain menu SubmenuMain menu Submenu Adjustments and Settings Using MenusMain Set up menu When PC input is selected Main Set up menu When video input is selectedMenu Operation Buttons MenuButton Procedure for Menu Operation Menu Configuration Adjustment and Setting Using MenusSet up menu Image adj. menuAspect ratio menu Position menuDecoder menu Resize menuOptions menu Capture startColor profile menu Language menuInformation menu Setting Aspect ratio and Resize Setting the Aspect ratioProject the image onto the screen Press the Menu button to end when adjustment is com- pleted Setting Aspect ratio and ResizeSelect Zoom with the cursor buttons  /  Optimum imageSet the Resize when Hdcp image is input from PC3 terminal Setting the ResizeSelect Resize with the cursor buttons  /  and press Enter Resize menu appears on the screenSet Resize to Zoom for optimum projected image Project the images to be included in your logo Editing and Projecting LogoSelect Logo with the cursor buttons  /  Press the Enter or the right cursor button Editing and projecting logo About lamp replacement Procedure for lamp replacementReplacing the Lamp Light source lamp and its lamp timeRemove the lamp unit Replacing the LampInsert the new lamp unit until it is fully Close the handle, and tighten the screwInsert the power cord into the wall outlet Resetting the lamp timeTo ensure the lamp time has been reset Press forPull out the power cord from the wall outlet Cleaning and Replacing the FilterClean the filter Reinstalling the filterPlied TroubleshootingSymptom Probable cause Corrective action TroubleshootingMessage Cause Contents What to do when these messages are displayedWhat to do when these messages are displayed For details on individually blinking indicators, please see  About warning indicatorsPlease follow the procedures below  Action to be taken upon warning indicationsPB, PR SpecificationsDimensions unit mm  Top Specifications Front  BottomPin arrangement  Y/C terminal  RS-232C IN/OUT terminal Pin number Signal name PC 1 terminal  PC 3 terminalCommunication Specifications Command Format RS-232C external control External control command table Dukane Corporation Audio Visual Products
Top Page Image Contents