Dukane 9100HC Cleaning and Replacing the Filter, Pull out the power cord from the wall outlet

Page 50

Cleaning and Replacing the Filter

Clean the filter regularly or it may not work satisfactorily, causing damage. If the filter is extremely dirty and cannot be cleaned, or if it is damaged, replace the filter with a new one (Lower filter: LC32087-002A/ Inner filter: LC32058-002A). Otherwise, dirt may get inside the unit and appear on the screen, preventing you from enjoying the video fully. If dirt has gotten in or if you need information about the filter, please consult the authorized dealer where you purchased the projector.

❈The air inlet filter on the right side cannot be removed. Please clean this filter regularly using, for example, a vacuum

cleaner.

1. Pull out the power cord from the wall outlet

•After the projector goes into the stand-by state with the [STAND BY] indicator on, pull out the power cord from the wall outlet.

2.Remove the filter

•When removing the lower filter:

Withdraw the lower filter backwards along the rail in the direction of the arrow.

•When removing the inner filter:

Push the claw at the base of the inner filter in the up- ward direction and draw the filter out.

3.Clean the filter

•Clean the filter with water and dry it, avoiding direct sun- light. In extremely soiled cases, use of a neutral deter- gent is recommended.

4. Reinstalling the filter

•When reinstalling the lower filter:

Reinstall the lower filter by inserting it into the projector.

•When reinstalling the inner filter:

Install the filter after engaging the two claws of the inner filter to the projector.

lower filter

inner filter

claw

●Put on rubber gloves when using a neutral detergent.

●After you wash a filter in water, make sure that the filter is completely dry before reinstalling, otherwise electric shocks or malfunctions may occur.

●Do not clean removable filters with a vacuum cleaner. Since these filters are soft, they can be sucked into the vacuum cleaner or otherwise damaged.

lower filter

inner filter

claw

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Model 9100HC FCC Information U.S.A. only Machine Noise Information Germany onlyPower supply voltage AC 120 Safety PrecautionDo not allow any unqualified person to install the unit For United For European KingdomHow To Replace The Fuse Do not cut off the main plug from this equipmentUsing the screen mode switch function Using the projectorHow to use the Screen Trigger terminal cable About burning-in of the D-ILA deviceContents AccessoriesControls and Features Front Side/ Top Surface/ Left SideControls and Features Rear Side/ Right Side/ Bottom SurfaceConnector Panel Indicator Display on the Control Panel Control Panel on the ProjectorLamp Indicator Stand by IndicatorOperate Indicator Temp IndicatorVideo button PC button Remote Control UnitVolume button Focus button Not functional on this unitScreen „ / Í button Remote Control’s signal transmitter Operate buttonVolume ª / · button Digital Zoom ª / · buttonsOpen the back cover Loading Batteries into the Remote ControlPrecautions for using batteries Load the batteriesInstalling the Projector Precautions for InstallationPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the Projector43 Screen Screen installationProjection Distance and Screen Size  Using as a wired Remote Control Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit When the remote control unit fails to work properly Video signals Connecting to Various DevicesSignals that can be input into the projector  Computer signalsConnecting to Various Devices  Allowable input signalsRight side of projector Connecting to Devices Connecting to Video Devices Connection Connecting to Computers  Control from external device Connection for controlling more than one projectorConnecting the Power Cord supplied  When using the projector, remove the Lens CapInsert the power cord into the wall outlet Basic Operation ProceduresPower On Basic OperationsAdjusting the Focus Ring Focus  Display using the direct buttonsAdjusting the Zoom Ring the screen size Basic OperationsPress Volume · 50 Adjusting the Sound VolumePower Off Plug out the power cord from wall outletFrequently used Convenient Functions Enlarging the ImageTurning Off Image and Sound Displaying a Still Picture Horiz.Keystone Display Removing the Trapezoidal Distortion of the Image Vert.keystone Display Quick Alignment function Using the Quick Alignment functionPress the Quick ALIGN. Quick Alignment button Main menu Adjustments and Settings Using MenusMenu Structure SubmenuAdjustments and Settings Using Menus Main menu SubmenuMain Set up menu When video input is selected Main Set up menu When PC input is selectedButton Menu Operation ButtonsMenu Procedure for Menu Operation Set up menu Adjustment and Setting Using MenusMenu Configuration Image adj. menuDecoder menu Position menuAspect ratio menu Resize menuColor profile menu Capture startOptions menu Language menuInformation menu Project the image onto the screen Setting Aspect ratio and ResizeSetting the Aspect ratio Select Zoom with the cursor buttons  /  Setting Aspect ratio and ResizePress the Menu button to end when adjustment is com- pleted Optimum imageSelect Resize with the cursor buttons  /  and press Enter Setting the ResizeSet the Resize when Hdcp image is input from PC3 terminal Resize menu appears on the screenSet Resize to Zoom for optimum projected image Select Logo with the cursor buttons  /  Editing and Projecting LogoProject the images to be included in your logo Press the Enter or the right cursor button Editing and projecting logo Replacing the Lamp Procedure for lamp replacementAbout lamp replacement Light source lamp and its lamp timeInsert the new lamp unit until it is fully Replacing the LampRemove the lamp unit Close the handle, and tighten the screwTo ensure the lamp time has been reset Resetting the lamp timeInsert the power cord into the wall outlet Press forClean the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Reinstalling the filterTroubleshooting PliedTroubleshooting Symptom Probable cause Corrective actionWhat to do when these messages are displayed Message Cause ContentsWhat to do when these messages are displayed Please follow the procedures below  About warning indicatorsFor details on individually blinking indicators, please see  Action to be taken upon warning indicationsSpecifications PB, PR Front SpecificationsDimensions unit mm  Top  Bottom PC 1 terminal Pin number Signal namePin arrangement  Y/C terminal  RS-232C IN/OUT terminal  PC 3 terminal RS-232C external control Communication SpecificationsCommand Format External control command table Dukane Corporation Audio Visual Products

9100HC specifications

The Dukane 9100HC is a cutting-edge ultrasonic welding system designed for high-performance applications in the healthcare and industrial sectors. Built to facilitate reliable and precise joining of thermoplastic materials, this advanced machine integrates several innovative technologies to ensure optimal performance and efficiency.

One of the standout features of the Dukane 9100HC is its enhanced ultrasonic technology. This system utilizes high-frequency ultrasonic waves, which generate localized heat at the interface of the materials being welded. This technology allows for faster welding cycles and minimizes the risk of damaging heat-sensitive components, making it ideal for applications that require delicate handling.

The 9100HC system is equipped with a user-friendly touchscreen interface, providing operators with easy access to important functionalities. This interface includes real-time process monitoring, allowing users to track key parameters such as temperature and amplitude during the welding process. Additionally, the system supports built-in data logging, enabling detailed analysis and quality assurance for critical applications.

Another significant characteristic of the Dukane 9100HC is its advanced energy management system. This system optimizes the energy used during the welding process, enhancing the overall efficiency and reducing operational costs. Moreover, the Dukane 9100HC is designed to accommodate a wide range of welding applications, thanks to its versatile tooling options. This adaptability makes it suitable for both small-scale operations and large manufacturing runs.

The machine's robust construction ensures durability and longevity, even in demanding environments. The compact design facilitates easy integration into existing production lines, while the ability to customize and configure the system according to specific production needs makes it a preferred choice among manufacturers.

Safety is paramount in Dukane’s design philosophy, and the 9100HC is no exception. It incorporates multiple safety features, including emergency stop buttons and protective enclosures, ensuring operator safety and compliance with industry standards.

Overall, the Dukane 9100HC represents a significant advancement in ultrasonic welding technology, delivering reliability, efficiency, and versatility to a wide array of applications within the healthcare and industrial sectors. With its innovative features and user-centric design, the Dukane 9100HC stands out as a premier solution for manufacturers seeking high-quality welding solutions.
Top Page Image Contents