Dukane 28A8035 manual AUTO-adjustment Confirm Screen, During AUTO-adjustment

Page 18

Adjustments and functions (continued)

< AUTO-adjustment >

The projector will automatically adjust four items (V POSIT, H POSIT, H PHASE, H SIZE, White level). When AUTO is selected (the cursor is moved from Manual Operation towards the right) the AUTO Confirm screen shown below will be displayed.

< AUTO-adjustment Confirm Screen >

While the AUTO confirmation screen is displayed as illustrated on the upper right, if you shift the cursor upward and select AUTO, the projector will perform auto-adjustment.

It will become as illustrated on the lower right.

If CANCEL is selected for three seconds, or if the RESET button on either the unit or the remote control is pressed, the green cursor will return to the value for the selected item (Manual Operation)

< During AUTO-adjustment >

At the lower right of the screen the word <AUTO> will flash in green letters.

When the auto-adjustment is completed the word <AUTO> will disappear. The auto-adjustment of the white level is cancelled by input switching and signal mode change.

S E T U P I N P U T I M A G E O P T .

VOLUME

 

 

BRIGHT

 

 

CONTRAST

 

 

V POSIT

123

AUTO

H POSIT

AUTO 111

 

H PHASE

CANCEL

 

H SIZE

1024

 

COLOR BAL

R

B

AUTO

Caution

∙ When start up screen is displayed ("NO INPUT IS DETECTED" or "SYNC IS OUT OF

RANGE" is displayed), SETUP menu items other than VOLUME cannot be set.

 

∙TINT cannot be adjusted with PAL/SECAM video signal input.

∙TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.

∙V.POSIT, H.POSIT, H.PHASE and H.SIZE cannot be adjusted with a VIDEO signal input.

∙Auto-adjustment will take about 10 to 15 seconds to complete.

∙In some cases auto-adjustment may not function normally, depending on the type of computer to which the unit is connected, and the signal sent.

∙Auto-adjustment may not perform normally with some images. Do not use with animated or dark images.

∙Carry out the auto-adjustment when the application, which is activated on the computer, is set to the maximum display.

∙After auto-adjustment the screen may become slightly dark due to the auto-adjustment of the signal level.

∙Auto-adjust can not be performed during freeze, during magnify, or during the initial screen display ("NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE").

INPUT

The menu INPUT serves for the selection of input source.

S E T U P

I N P U T

I M A G E O P T .

SETUP

INPUT

IMAGE OPT .

 

 

 

 

 

 

 

 

 

 

S Y S T E M

 

RGB1

 

 

RGB1

 

 

AUTO

 

 

 

 

 

 

RGB2

 

 

RGB2

 

 

NTSC

 

VIDEO

 

 

V I DEO

 

 

PAL

 

 

 

 

 

 

 

 

 

 

SECAM

 

 

 

 

 

 

 

 

 

 

NTSC4.43

 

 

 

 

 

 

 

 

 

 

M-PAL

 

 

 

 

 

 

 

 

 

 

N-PAL

Adjustment Item

Details of adjustment

 

 

RGB 1

Selects the RGB 1 terminal.

 

 

RGB 2

Selects the RGB 2 terminal.

 

 

VIDEO

Selects the VIDEO terminal.

 

 

 

Selects the video signal systems. In normal circumstances, select AUTO. AUTO does not

SYSTEM

support N-PAL.

When the picture (Video) is abnormal (no color), selects the input signal mode (NTSC,

 

 

PAL, SECAM, NTSC4.43 M-PAL and N-PAL). To input N-PAL signals, select N-PAL.

 

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents
28A8035 For the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursBe careful in handling the power cord Do not stare directly into the laser apertureUse of batteries When you are not going to use for a CleaningHandle the power cord carefully Clean inside the unit at least once two yearsVolume When you are not going to use For a long timeDo not place this unit where it gets hot Cleaning the lensContents of shipping box Video input terminal Remote control sensor Main Power switchAC in socket RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partInstallation Example of the projector and screen installationHow to use foot adjusters Basic operations To project the pictureTo turn off the power Press the STANDBY/ON button, for 1 secondFreeze Function Adjustments and functions To return to the initial settingMemory function Numerical display items V POSIT, H Posit etc How to use the SET UP menuBar display items VOLUME, Bright etc Manual OperationDuring AUTO-adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen Adjustment Item Details of adjustmentReveal Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Connection to the control signal terminal Control signal terminalMouse emulation PS/2 mouse ADB Mac mouseSerial mouse Communication Control command tableControl command table RS232C cable ReferenceCommand data Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeCleaning the air filter Air filter Filter coverHow to replace lamp Remove the lamp coverLoosen two screws and pull the handle to remove Lamp Install the lamp cover and fix it using screws Reset the lamp timeLamp On-screen display Indicator displayMessage table ActionWhen you think something wrong Dimension diagram RCA Jack terminal Input terminal Input/OutputOperating guide RGB cable Legal Information St. Charles, IL Fax Mail avsales@dukane.com