Dukane 28A8035 Connection to the video signal terminals, Connection to the RGB signal terminal

Page 20

Connection to the video signal terminals

1. Input signal

S-VIDEO signal			Luminance signal	1.0Vp-p, 75Ω termination
S-VIDEO signal			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination
			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination

VIDEO signal				1.0Vp-p, 75Ω termination

AUDIO signal		Input		200mVrms, 20kΩ below (MAX 3.0Vp-p)

		Output		0~200mVrms, 1kΩ
		Output		0~200mVrms, 1kΩ

2. Signal input terminal

Chrominance signal

Luminance signal

	Ground	Ground
	Ground
	S VIDEO input (Mini DIN4 pin)
Caution	Video input signal terminals have priority in the following order.
Caution
	1 S-VIDEO input terminal 2 RCA jack input terminal

Even when the video signal is displayed, only an audio signal is output to RGB audio output terminals.

Connection to the RGB signal terminal

1. Input / output signal

	Video signal		Analog 0.7Vp-p 75Ω termination (Positive polarity)

	Horizontal sync signal		TTL level (Positive/negative polarity)

	Vertical sync signal		TTL level (Positive/negative polarity)

	Composite sync signal		TTL level

	Audio signal	Input	200mVrms, 20kΩ below (MAX 3.0Vp-p)

		Output	0~200mVrms, 1kΩ
		Output	0~200mVrms, 1kΩ

2. Signal input / output terminal

1	Video signal (Red)	9	N.C

2	Video signal (Green)	10	Ground

3	Video signal (Blue)	11	N.C

4	N.C	12	DDC (Display Data channel) RGB1 only

5	N.C	13	Horizontal/Composite sync signal

6	Ground (for R)	14	Vertical sync signal

7	Ground (for G)	15	DDC (Display Data channel) RGB1 only

8	Ground (for B)

5 1

106

15 11

D-sub 15pin shrink terminal (Female)

	Caution	Do not use RGB cable other than that specified.
	Caution	Some RGB cable may not operate DDC (Display Data Channel)
		Some RGB cable may not operate DDC (Display Data Channel)
		because there are not connect from pin NO. 15 to pin NO. 12 .

20

Image 20

Contents 28A8035 For the Customers in U.K Video signal cables Power cordBefore use Instructions to UsersDo not look directly at the lens when Lamp is lit Do not install this unit in an unstable placeDo not use power supplies other Than that specified If any abnormality occursBe careful in handling the power cord Do not stare directly into the laser apertureCleaning Handle the power cord carefullyUse of batteries When you are not going to use for a Clean inside the unit at least once two yearsWhen you are not going to use For a long time Do not place this unit where it gets hotVolume Cleaning the lensContents of shipping box Remote control sensor Main Power switch AC in socketVideo input terminal RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partHow to use foot adjusters InstallationExample of the projector and screen installation Basic operations To project the pictureTo turn off the power Press the STANDBY/ON button, for 1 secondFreeze Function Memory function Adjustments and functionsTo return to the initial setting How to use the SET UP menu Bar display items VOLUME, Bright etcNumerical display items V POSIT, H Posit etc Manual OperationAUTO-adjustment AUTO-adjustment Confirm ScreenDuring AUTO-adjustment Adjustment Item Details of adjustmentReveal Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeComputer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Mouse emulation Connection to the control signal terminalControl signal terminal Serial mouse PS/2 mouseADB Mac mouse Control command table Control command tableCommunication RS232C cable ReferenceCommand data Procedure of getting the Projector status Procedure of setting the Projector statusProcedure of default setting the Projector status Example of command errorExample of system setup Connecting various equipmentAC Inlet Computer Note type ComputerDesk typeCleaning the air filter Air filter Filter coverLoosen two screws and pull the handle to remove Lamp How to replace lampRemove the lamp cover Lamp Install the lamp cover and fix it using screwsReset the lamp time Indicator display Message tableOn-screen display ActionWhen you think something wrong Operating guide RGB cable Dimension diagramRCA Jack terminal Input terminal Input/Output Legal Information St. Charles, IL Fax Mail avsales@dukane.com