Dukane 28A8035 manual For the Customers in U.K

Page 2

FOR THE CUSTOMERS IN U.K

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K PLEASE REFER TO THE NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferable a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply.

WARNING: THIS EQUIPMENT MUST BE EARTHED

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow=Earth, Blue=Neutral, Brown=Live.

Green & Yellow to Earth

Brown to Live

 

Fuse

Blue to Neutral

Cord Clamp

As these colours may not correspond with the coloured makings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol

 

 

or coloured Green or Green and Yellow.

 

 

The wire coloured Blue must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents
28A8035 For the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursBe careful in handling the power cord Do not stare directly into the laser apertureUse of batteries When you are not going to use for a CleaningHandle the power cord carefully Clean inside the unit at least once two yearsVolume When you are not going to use For a long timeDo not place this unit where it gets hot Cleaning the lensContents of shipping box Video input terminal Remote control sensor Main Power switchAC in socket RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partHow to use foot adjusters InstallationExample of the projector and screen installation Basic operations To project the pictureTo turn off the power Press the STANDBY/ON button, for 1 secondFreeze Function Memory function Adjustments and functionsTo return to the initial setting Numerical display items V POSIT, H Posit etc How to use the SET UP menuBar display items VOLUME, Bright etc Manual OperationDuring AUTO-adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen Adjustment Item Details of adjustmentReveal Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeComputer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Mouse emulation Connection to the control signal terminalControl signal terminal Serial mouse PS/2 mouseADB Mac mouse Communication Control command tableControl command table RS232C cable ReferenceCommand data Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeCleaning the air filter Air filter Filter coverLoosen two screws and pull the handle to remove Lamp How to replace lampRemove the lamp cover Lamp Install the lamp cover and fix it using screwsReset the lamp time On-screen display Indicator displayMessage table ActionWhen you think something wrong Operating guide RGB cable Dimension diagramRCA Jack terminal Input terminal Input/Output Legal Information St. Charles, IL Fax Mail avsales@dukane.com