Dukane 28A8035 manual Be careful in handling the power cord

Page 5

Warning

Be careful in handling the power cord.

Do not scratch, damage or process the power cord. Do not bend it forcibly. Also do not put a heavy object on it, do not heat it and do not pull it. If you do, the power cord may be damaged and it may cause a fire, electric shock, etc.

Do not pull the cord.

Do not put a heavy object on it.

Do not damage the cord.

Do not put it near a heating

device.

Be careful that this unit is not placed

on the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc. If the cord is covered with a carpet, etc. a heavy object may be put on it without your realizing it.

If the cord is damaged (core wire is exposed, disconnected, etc.), ask

your dealer to replace it. It may cause a fire, electric shock, etc.

Check that no dirt adheres to the

power plug and fully insert without any play. If dirt adheres or the connection is incomplete, it may cause a fire, electric shock, etc.

The outer shield of power cord must be connected to ground.

If you do not, it may cause a electric shock.

ENGLISH

Do not stare directly into the laser aperture.

The laser pointer on the remote control unit radiates the laser beam from the laser aperture.

Do not stare into the laser aperture or radiate the laser beam to other persons as the laser emitted is a class 2 laser and it could damage you vision , etc.

Especially pay attention if children are present.

The three labels below are caution labels for the laser beam.

CAUTION

LASER RADIATION -

DO NOT STARE INTO BEAM

WAVE LEGTH : 670nm

MAX. OUTPUT : 1mW

CLASS 2 LASER PRODUCT

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASS 2

RAYONNEMENT LASER

MANUFACTURED

NE PAS REGARDER DANS

 

LE FAISCEAU APPAREIL

August-97

A LASER DE CLASSE 2

 

LASER-STRAHLUNG

 

NICHT IN DEN STRAHL

 

BLICKEN LASAER KLASSE 2

MANUFACTURER:A

 

 

C A U T I O N

LASER RADIATION -

DO NOT STARE INTO BEAM

WAVE LEGTH : 670nm

MAX. OUTPUT : 1mW

CLASS 2 LASER PRODUCT

AVOIDE EXPOSURE-LASER

RADIATION IS EMITTED

FROM THIS APERTURE

LASER APERTURE

5

Image 5
Contents 28A8035 For the Customers in U.K Power cord Video signal cablesBefore use Instructions to UsersDo not install this unit in an unstable place Do not look directly at the lens when Lamp is litDo not use power supplies other Than that specified If any abnormality occursDo not stare directly into the laser aperture Be careful in handling the power cordHandle the power cord carefully CleaningUse of batteries When you are not going to use for a Clean inside the unit at least once two yearsDo not place this unit where it gets hot When you are not going to use For a long timeVolume Cleaning the lensContents of shipping box AC in socket Remote control sensor Main Power switchVideo input terminal RGB input terminalRemote control transmitter Names and functions of each part How to insert batteriesHow to use foot adjusters InstallationExample of the projector and screen installation To project the picture Basic operationsPress the STANDBY/ON button, for 1 second To turn off the powerFreeze Function Memory function Adjustments and functionsTo return to the initial setting Bar display items VOLUME, Bright etc How to use the SET UP menuNumerical display items V POSIT, H Posit etc Manual OperationAUTO-adjustment Confirm Screen AUTO-adjustmentDuring AUTO-adjustment Adjustment Item Details of adjustmentReveal Connection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Type Example of computer signalComputer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Mouse emulation Connection to the control signal terminalControl signal terminal Serial mouse PS/2 mouseADB Mac mouse Control command table Control command tableCommunication RS232C cable ReferenceCommand data Procedure of setting the Projector status Procedure of getting the Projector statusProcedure of default setting the Projector status Example of command errorConnecting various equipment Example of system setupAC Inlet Computer Note type ComputerDesk typeAir filter Filter cover Cleaning the air filterLoosen two screws and pull the handle to remove Lamp How to replace lampRemove the lamp cover Lamp Install the lamp cover and fix it using screwsReset the lamp time Message table Indicator displayOn-screen display ActionWhen you think something wrong Operating guide RGB cable Dimension diagramRCA Jack terminal Input terminal Input/Output Legal Information Mail avsales@dukane.com St. Charles, IL Fax