Christie Digital Systems 38-VIV208-01 user manual Basic Operation, Turning On the Projector

Page 19

Basic Operation

Turning On the Projector

1

Complete peripheral connections (with a computer, VCR, etc.)

 

before turning on the projector.

2

Connect the projector's AC power cord into an AC outlet. The

 

POWER indicator flashes red in a moment and turns on red.

3

Press the POWER ON-OFF button on the top control or on the

 

remote control. The POWER indicator turns green, and the

 

cooling fans start to operate. The preparation display appears on

 

the screen and the count down starts. (A captured image can

 

be used as the preparation display. See “Capture” on page 38.)

4

After the count-down, the input source that was selected last

 

and the Lamp mode status icon appear on the screen.

26

The preparation display disappears after 30 seconds.

Selected Input Source and Lamp Mode

Lamp mode

(See page 40 for Lamp mode.)

Turning Off the Projector

1

Press the POWER ON-OFF button on the top control or on the

 

remote control, and a message "Power off?" appears on the

 

screen.

2

Press the POWER ON-OFF button again to turn off the

 

projector. The POWER indicator starts to flash red, and it

continues while the cooling fans are operating (for about 90 seconds).

3

When the projector has cooled down enough to be turned on

 

again, the POWER indicator lights red. Then you can disconnect

the AC power cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

DO NOT DISCONNECT AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE POWER INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN SHORTENING LAMP LIFE.

The message disappears after 4 seconds.

NOTE

The projector cannot be turned on during the cooling period with the POWER indicator flashing red. You can turn it on again after the POWER indicator lights red.

When the On start function is on, this projector is turned on automatically by connecting the AC power cord to an AC outlet. (See page 39 for the On start function.)

This projector monitors internal temperature and automatically controls the running speed of the cooling fans.

If the WARNING indicator flashes or lights red, see “Warning Indicator” on page 41.

19

Image 19
Contents Model Table of Contents Risk of Electric Shock Do not Open To the UserVoor de klanten in Nederland Safety InstructionsMoving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationFederal Communication Commission Notice Compliance200 240 V AC ComplianceFor Continental Europe For the U.S.A. and CanadaFeatures and Design Bottom Part Names and FunctionsFront BackTerminal Part Names and FunctionsTop Power ON-OFF buttonSignal Emission indicator Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangeAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Connecting to Video EquipmentProjector Turning On the Projector Basic OperationTurning Off the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentDirect Operation Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Input Source Selection Computer InputMode Computer InputComputer System Selection AutoTo store adjustment data Computer Adjustment AutoAuto PC Adj Computer Adjustment Manual To clear adjustment data ResetMode free Display area To store adjustment dataImage button Standard Real Image Level SelectionStandard RealImage Level Adjustment Screen Size Adjustment Auto Video InputInput Source Selection Video, S-Video Input button Video Computer Video button VideoInput button Computer Video Computer button Video InputInput Source Selection Component, RGB Scart 21-Pin Component RGB ScartAV System Menu Video or S-Video Video System SelectionVideo or S-Video ComponentImage button Standard Cinema CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting To change the code for the projector To change the code for the remote controlProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the items below Cleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix ServiceProjector Condition Indicators and Projector ConditionInput PC AdjustImage Select Image Adjust Screen Menu TreeImage Select 575pSettingFreq Compatible Computer SpecificationsKHz Technical Specifications Terminal HDB15-PIN Pin Configuration Configurations of TerminalsTerminal DVI-I Pin Configuration MAC Adapter DVI Cable COMPONENT-VGA Cable SCART-VGA Cable USB Connector Series BTerminal Mini DIN 8-PIN Pin Configuration Optional PartsAttaching the Lens Cover Page Part No -A 610 309 1143 1AA6P1P4208-- MT3K