Christie Digital Systems 020-000141-01 user manual Lamp Replacement, Indicators

Page 63

Maintenance and Care

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP 1/2 REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing when the LAMP 1/2 REPLACE indicators should light is depending on the lamp mode.

Indicators

WARNING:

TURN OFF THE UV LAMP BEFORE

OPENING THE LAMP COVER.

Lamp replacement icon

Allow the projector to cool, for at least 45 minutes before you open Lamp Cover. The inside of the projector can become very hot.

LAMP 1 / 2 REPLACE indicators

CAUTION

Note:

s4HE ,AMP,REPLACEMENTEICON WILLENOTEAPPEAR WHEN THE $ISPLAYYFUNCTION ISTSETOTO h/FFvvP OR DURINGUh&REEZEvvP

Follow these steps to replace the lamp.

For continued safety, replace with a lamp assembly of the same type.

Do not drop the lamp assembly or touch a glass bulb! The glass can shatter and may cause injury.

1Check the number of lamp to be replaced on the Lamp Status Display.

2Turn off the projector, press the Main On/Off Switch to Off and unplug the AC power cord from the AC outlet. Let the projector cool for at least 45 minutes.

3Loosen a screw on the Lamp Cover. Slide and open the Lamp Cover until it makes a clicking sound. (See the right figure.)

4Loosen two screws and pull out the Lamp to be replaced by grasping handle.

5Replace the Lamp with a new one and tighten two screws. Make sure the Lamp is set properly.

6Put the Lamp Cover back and tighten a screw.

7Connect the AC Power Cord to the projector and turn on the projector.

8Reset the Lamp Replacement Counter. (Refer to section "Resetting the Lamp Counter" on page 62.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

LAMP
COVER	SCREW
	LAMP 2

SCREWS

LAMP 1

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 1.

CAUTION : DO NOT OPERATE THE PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing both 2 lamps at a time.

LX1000 User Manual	61
020-000141-01 Rev. 1 (05-2009)

Image 63

Contents LX1000 Page = Lens not included Features and Design Table of Contents Risk of Electric Shock Do not Open To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United States and Canada ComplianceCanadian Radio Interference Regulations Part Names and Functions Front Back=Kensington Security Slot Sub 15-PIN Input Terminal Terminals and ConnectorsUSB Connector Series B Reset buttonSide Control Side Control and IndicatorsIndicators Analog Mini D-sub 15 pin Configurations of TerminalsUSB Connector Series B Control Port Connector D-sub 9 pinRemote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Remote Control Code Pressing Image ADJ ButtonNumber of Times Installation Lens InstallationPositioning Projector When the lens is shifted to rightmost Lens Shift AdjustmentPicture Level and Pitch Adjustment When the lens is shifted to leftmostTerminals of Projector Replacement of TerminalConnecting to Computer Cables used for connectionTerminals of the projector RGB Scart Connecting to Video EquipmentFor the U.S.A. and Canada For Continental Europe Connecting the AC Power CordEnter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Unplug the AC power cord from the AC outletOn-Screen Menu How to Operate the On-Screen MenuRemote Control Side ControlMenu Bar Auto PC Adjustment Zoom Adjustment Side ControlFocus Adjustment Lens Shift AdjustmentInformation Menu InformationOperating with Remote Control Image ADJ. button Timer buttonShutter button Filter buttonInput Remote Control OperationRemote Control Remote Control button operation Input SelectionInput Menu When Selecting the Input 1 with DVI/D-sub 15 terminalsComputer Input Source Selection Menu OperationPb/Cb, Pr/Cr Video Input Source SelectionRGB Scart RGB AV HdcpSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemAuto PC adj Auto PC AdjustmentPC Adjust Menu Direct OperationManual PC Adjustment To store the adjusted data ResetMode free To clear the adjusted dataImage Select Menu Image Level SelectionStandard Real Image1 Image SEL. button StandardScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackStandard Cinema Image1 Image SEL. button Provide the image at the normal video aspect ratio Keystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeDEL Color MMenu Color PaletteGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLogo Logo selectCapture Change the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Fan control Lamp modeLamp control Filter controlRC sensor Security On startSecurity Key lock PIN code lockChange the PIN Code Change the PIN Code Lock settingLamp counter ShutterProtection ManagementFactory default Filter counterTest pattern Filter Instructions Maintenance and CareModel No. of your projector LX1000 Replacement Filter Cartridge Service Parts CodeReset the filter counter and the scroll counter p.59 Replacing the Filter CartridgeScroll counter Resetting the Filter CounterResetting the Scroll Counter Filter counterLamp Status Display Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp ManagementLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Order Replacement Lamp Resetting the Lamp CounterLamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingColor is strange Power is turned off Information Information Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectSetting Sss ssOFF Approx .5 seconds on Seconds OFF Indicators and Projector ConditionProjector is operating normally Sss ssBLINKING Fasts TLamp Replace 1 Projector is detecting abnormal conditionAppears on the screen and the Warning Filter Display Compatible Computer SpecificationsON-SCREEN Resolution Freq.kHz Freq.HzVGA Technical Specifications ODELD.O Optional PartsConfigurations of Terminals PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Screw Holes for Ceiling Mount Screw M8 Depth 0.393 DimensionsAmericas Europe, Middle East & AfricaAsia Pacific