Acer S3811 manual Mainboard Components, Label Component

Page 10

Mainboard Components

No	Label	Component
1	CPU Socket	LGA1156

2	ATX12V	4-pin +12V power connector

3	SYS_FAN	System cooling fan connector

4	CPU_FAN	CPU cooling fan connector

5	DIMM1~4	240-pin DDR3 SDRAM slots
6	ATX_POWER	Standard 24-pin ATX power connector

7	USB1/2/4	Front panel USB headers

8	USB 3	Front panel CR headers

9	SATA1~2	Serial ATA connectors

10	GPIO1~2	GPIO header 1~2

11	BIOS_FLASH	Reflash BIOS connectors

12	F_PANEL	Front panel switch/LED header

13	BIOS_WP	BIOS Write protection connectors

14	CLR_CMOS	Clear CMOS jumper

15	ME_Enable	ME Enable/Disable header

16	SPDIF_OUT	SPDIF out header

17	SPK	Internal speaker header

18	F_AUDIO Front	panel audio header

19	PCIE16X	Express x1 slot

20	PCIEX 1X	Express x1 slot

This concludes Chapter 1. The next chapter explains how to install the motherboard.

4

Image 10

Contents Imedia S3811 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface Page Introducing the Motherboard IntroductionFeatures Dimensions and weight Bios FirmwareIntegrated I/O Mainboard Components Label ComponentBlock Diagram Imedia S3811 Icon Component DescriptionRear view Color/Use Headphone Audio Jack Function Table1CH Port Introduction Component DescriptionKeyboard PS/2 or USB, manufacturing option System PeripheralsMouse PS/2 or USB, manufacturing option SpeakersCard Reader Option Specification Hardware Specifications and ConfigurationsBios Hotkey List Main Board Major ChipsVideo Interface System MemoryCache Memory Audio InterfaceUSB Port Power ManagementIDE Interface Devices Idle Shut DownGlobal Standby Mode Power Management Function Acpi support functionDevice Standby Mode Suspend ModeStandard Configuration Using BiosAbout the Setup Utility Entering the Setup UtilitySetup Utility Menus Updating the Bios Product Information Item HelpStandard Cmos Features Date and TimeSata Port0 Auto A.R.T. EnabledUAHCI Port1 /Port2 Halt On All, But KeyboardQuick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled Sequence from Available devices Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message DisabledAdvanced Chipset Features Integrated Peripherals Power Management Setup Restore On AC Power Loss Last State Smart Fan Enabled PC Health StatusSpread Spectrum Enabled Frequency/Voltage ControlSupervisor Password Not Installed Bios Security FeaturesLoad Default Settings User Password Not InstalledSave & Exit Setup Exit Without SavingMachine Disassembly and Replacement General Information Before You BeginOpening the chassis Standard Assembly ProcessRemoving PSU bracket Removing HDD bracket Removing front bezelInsert the ODD devices Setting the Motherboard Page 3x1G 1x1G2x1G 4x1GAssembly motherboard Insert the system FanPage Front Pulling in HDD &ODD Sata cable on Motherboard Insert VGA card Insert the PSU Long for HDD used Short for ODD used Overview Standard Disassembly Process Removing the power-supplyPage Pulling out the Sata ODD cable and Sata HDD cable Removing the HDDFrontBack Removing the VGA Card Pulling out the Audio/USB1/CR/PANEL cableRemoving system Fan Removing the Main Board Page Release the four latch show bellow then remove the Memory Removing the ODD Removing the ODD bracketRemoving the ODD bracket Pushing the Cable Removing power switch & HDD-LED holder Page Machine Disassembly and Replacement Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Main board and Memory Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioParallel/Serial Ports Error Symptom Action/FRU Video and MonitorPower Supply KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Installing the Motherboard in a Case Jumper and Connector InformationSafety Precautions Choosing a Computer CaseChecking Jumper Settings Setting JumpersJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting Case Components Connecting 24-pin power cableATX12V ATX 12V Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionAtxpoweratx 24-pin Power Connector Pin Signal Name Pin Signal NameReset Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Power SwitchInstalling the Processor Installing HardwareBefore installing the Processor CPU Installation Procedure Following illustration shows CPU installation componentsInstallation Procedure Installing Memory ModulesMemory Memory Bus Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE1X1 SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~4 Serial ATA connectors Spdifo Spdif out headerOptionFRU Field Replaceable Unit List Exploded Diagram ChassisP5-15L w/ card reader ME BOMPage ChassisP5-15L w/o card reader ME BOM Page FRU List