Acer S3811 CPU Installation Procedure, Following illustration shows CPU installation components

Page 88

CPU Installation Procedure

The following illustration shows CPU installation components.

AOpening of the Load Plate Put your thumb on the tail of the load plate and press the tail down Rotate the load plate to fully open

position.

B.Disengaging of the Load Lever· Hold the hook of lever and pull it to the left side to clear retention tab. Rotate the load lever to fully open position.

C.Removing the Cap· Be careful not to touch the contact at any time.

D.Inserting the Package·Grasp the package. Ensure to grasp on the edge of the substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.

E.Closing the Load Plate·Rotate the load plate onto the package IHS (Intergraded Heat Spreader).· Engage the load lever while pressing down lightly onto the load plate.·Secure the load lever with the hook under retention tab.

F.Fasten the cooling fan supporting base onto the CPU socket on the motherboard.

G.Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.

1.To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary.

2.DO NOT remove the CPU cap from the socket before installing a CPU.

3.Return Material Authorization (RMA) requests will be accepted

only if the motherboard comes with the cap on the LGA1156 socket.

82

Image 88

Contents Imedia S3811 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface Page Introducing the Motherboard IntroductionFeatures Dimensions and weight Bios FirmwareIntegrated I/O Mainboard Components Label ComponentBlock Diagram Imedia S3811 Icon Component DescriptionRear view Color/Use Headphone Audio Jack Function Table1CH Port Introduction Component DescriptionSystem Peripherals Mouse PS/2 or USB, manufacturing optionKeyboard PS/2 or USB, manufacturing option SpeakersCard Reader Option Hardware Specifications and Configurations Bios Hotkey ListSpecification Main Board Major ChipsSystem Memory Cache MemoryVideo Interface Audio InterfacePower Management IDE InterfaceUSB Port Devices Idle Shut DownPower Management Function Acpi support function Device Standby ModeGlobal Standby Mode Suspend ModeUsing Bios About the Setup UtilityStandard Configuration Entering the Setup UtilitySetup Utility Menus Updating the Bios Product Information Item HelpStandard Cmos Features Date and TimeA.R.T. Enabled UAHCI Port1 /Port2Sata Port0 Auto Halt On All, But KeyboardQuick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled Sequence from Available devices Removable Device Priority Press Enter Boot Up NumLock On USB Beep Message DisabledAdvanced Chipset Features Integrated Peripherals Power Management Setup Restore On AC Power Loss Last State Smart Fan Enabled PC Health StatusSpread Spectrum Enabled Frequency/Voltage ControlBios Security Features Load Default SettingsSupervisor Password Not Installed User Password Not InstalledSave & Exit Setup Exit Without SavingMachine Disassembly and Replacement General Information Before You BeginOpening the chassis Standard Assembly ProcessRemoving PSU bracket Removing HDD bracket Removing front bezelInsert the ODD devices Setting the Motherboard Page 1x1G 2x1G3x1G 4x1GAssembly motherboard Insert the system FanPage Front Pulling in HDD &ODD Sata cable on Motherboard Insert VGA card Insert the PSU Long for HDD used Short for ODD used Overview Standard Disassembly Process Removing the power-supplyPage Pulling out the Sata ODD cable and Sata HDD cable Removing the HDDFrontBack Removing the VGA Card Pulling out the Audio/USB1/CR/PANEL cableRemoving system Fan Removing the Main Board Page Release the four latch show bellow then remove the Memory Removing the ODD Removing the ODD bracketRemoving the ODD bracket Pushing the Cable Removing power switch & HDD-LED holder Page Machine Disassembly and Replacement Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Error Symptoms List Error Symptom Action/FRU Processor / Processor FanMain board and Memory Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioError Symptom Action/FRU Video and Monitor Power SupplyParallel/Serial Ports KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Jumper and Connector Information Safety PrecautionsInstalling the Motherboard in a Case Choosing a Computer CaseChecking Jumper Settings Setting JumpersJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting Case Components Connecting 24-pin power cableSysfan Cooling Fan Power Connector Pin Signal Name Function Atxpoweratx 24-pin Power Connector Pin Signal NameATX12V ATX 12V Power Connector Pin Signal Name Pin Signal NamePin Signal Name Function Power/Sleep/Message waiting LEDReset Switch Power SwitchInstalling the Processor Installing HardwareBefore installing the Processor CPU Installation Procedure Following illustration shows CPU installation componentsInstallation Procedure Installing Memory ModulesMemory Memory Bus Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE1X1 SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~4 Serial ATA connectors Spdifo Spdif out headerOptionFRU Field Replaceable Unit List Exploded Diagram ChassisP5-15L w/ card reader ME BOMPage ChassisP5-15L w/o card reader ME BOM Page FRU List