Acer S3811 manual ChassisP5-15L w/o card reader ME BOM

Page 97

Chassis_P5-15L w/o card reader ME BOM

Item			Description	Item			Description

1			SM_SIDE_COVER	22			SM_ODD_CAGE

2			SCREW-6-32-6L	23			WCL-10

3			RUBBER_FOR_POWER_BKT	24			SM_HDD_CAGE

4			SM_POWER_BKT	25			SM_FRONT_PLATE

5			CABLE CLIP	26			RIVET_32_FLAT_HEAD

6			SM_PCI_SLOT_COVER	27			RIVET_32_UMBRELLA_HEAD

7			SM_PCI_EMI_SHIELDING	28			TOP COVER CABLE ROUTING

8			SM_PCI_CLAMP	29			TOP-COVER

9			SM_REAR_PLATE	30			TOP-MAIN_BEZEL

10			SM_POWER_ASM_BKT	31			SPRING_ODD_EJECTION

11			SM_MB_BKT	32			POWER BUTTOM

12			STANDOFF	33			MYLAR

13			CLIP	34			HDD-LENS

14			STANDOFF_FIX	35			EJECT_CONNECT

15			SCREW-FOR-ODD_CAGE	36			EJECT-BOTTOM

16			SM_C_BASE	37			FRONT-MAIN_BEZEL-W_CR

17			CHASSIS FOOT	38			ODD-DOOR

18			SM_DUST_COVER	39			SPRING_DOOR_ODD

19			LED HOUSING	40			FRONT-COVER

20			USB CABLE ASSY	41			PB LOGO
20			(without card reader)	41			PB LOGO
			(without card reader)

21			POWER PCB

91

Image 97

Contents Imedia S3811 Service Guide Revision History Date Chapter UpdatedCopyright Conventions Preface Page Introduction Introducing the MotherboardFeatures Dimensions and weight Bios FirmwareIntegrated I/O Label Component Mainboard ComponentsBlock Diagram Icon Component Description Imedia S3811Rear view Color/Use Headphone Audio Jack Function Table1CH Component Description Port IntroductionMouse PS/2 or USB, manufacturing option System PeripheralsKeyboard PS/2 or USB, manufacturing option SpeakersCard Reader Option Bios Hotkey List Hardware Specifications and ConfigurationsSpecification Main Board Major ChipsCache Memory System MemoryVideo Interface Audio InterfaceIDE Interface Power ManagementUSB Port Devices Idle Shut DownDevice Standby Mode Power Management Function Acpi support functionGlobal Standby Mode Suspend ModeAbout the Setup Utility Using BiosStandard Configuration Entering the Setup UtilitySetup Utility Menus Updating the Bios Item Help Product InformationDate and Time Standard Cmos FeaturesUAHCI Port1 /Port2 A.R.T. EnabledSata Port0 Auto Halt On All, But KeyboardQuick Boot Enabled Advanced Bios FeaturesQuiet Boot Enabled Sequence from Available devices Removable Device Priority Press Enter USB Beep Message Disabled Boot Up NumLock OnAdvanced Chipset Features Integrated Peripherals Power Management Setup Restore On AC Power Loss Last State PC Health Status Smart Fan EnabledFrequency/Voltage Control Spread Spectrum EnabledLoad Default Settings Bios Security FeaturesSupervisor Password Not Installed User Password Not InstalledExit Without Saving Save & Exit SetupMachine Disassembly and Replacement Before You Begin General InformationOpening the chassis Standard Assembly ProcessRemoving PSU bracket Removing front bezel Removing HDD bracketInsert the ODD devices Setting the Motherboard Page 2x1G 1x1G3x1G 4x1GInsert the system Fan Assembly motherboardPage Front Pulling in HDD &ODD Sata cable on Motherboard Insert VGA card Insert the PSU Long for HDD used Short for ODD used Overview Removing the power-supply Standard Disassembly ProcessPage Removing the HDD Pulling out the Sata ODD cable and Sata HDD cableFrontBack Pulling out the Audio/USB1/CR/PANEL cable Removing the VGA CardRemoving system Fan Removing the Main Board Page Release the four latch show bellow then remove the Memory Removing the ODD bracket Removing the ODDRemoving the ODD bracket Pushing the Cable Removing power switch & HDD-LED holder Page Machine Disassembly and Replacement Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages ListSpecifics about the type and location of the memory error Error Symptom Action/FRU Processor / Processor Fan Error Symptoms ListMain board and Memory Hard Disk DriveAudio Error Symptom Action/FRU CD/DVD-ROM DrivePower Supply Error Symptom Action/FRU Video and MonitorParallel/Serial Ports KeyboardOther Problems Error Symptom Action/FRUUndetermined Problems Safety Precautions Jumper and Connector InformationInstalling the Motherboard in a Case Choosing a Computer CaseSetting Jumpers Checking Jumper SettingsJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case ComponentsAtxpoweratx 24-pin Power Connector Pin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionATX12V ATX 12V Power Connector Pin Signal Name Pin Signal NamePower/Sleep/Message waiting LED Pin Signal Name FunctionReset Switch Power SwitchInstalling the Processor Installing HardwareBefore installing the Processor Following illustration shows CPU installation components CPU Installation ProcedureInstallation Procedure Installing Memory ModulesMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard DrivesPCIE1X1 Slot Installing Add-on CardsOnboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional DevicesSpdifo Spdif out headerOption Sata 1~4 Serial ATA connectorsChassisP5-15L w/ card reader ME BOM FRU Field Replaceable Unit List Exploded DiagramPage ChassisP5-15L w/o card reader ME BOM Page FRU List