Acer RB23WABAS service manual Scope

Page 3

2

ACER H233H

1. Product Specification

Go to cover page

This model combine with three platform. See below explanation.

1.Scaler IC:RTD2482D used in VGA ,DVI and HDMI port Using simply word to define it(1A1D1H)

2.Scaler IC:RTD2482 used in VGA and HDMI port. Using simply word to define it(1A1D)

3.Scaler IC:RTD2482RD used in VGA ,DVI and HDMI port

.Using simply word to define it.(1A1D1H+OD)

The product specification demonstrate all of the model:

1.1 SCOPE

This document defines the design and performance requirements for a 23W inch diagonal , flat panel monitor . The display element shall be a 1920x1080 resolution TFT-LCD (Thin Film Transistor Liquid Crystal Display).16.7M color(Hi-FRC) images are displayed on the panel.Video input signals are analog RGB (0.7Vp-

p). When the system is powered-on , previously stored screen parameters for a pre-defined mode will be recalled if the operating mode is one of stored in memory( 2213 factory timing mode).This monitor operates normal by non-interlaced mode.

DDC (Display Data Channel) function is DDC2Bi compliance. Power saving function complies with the DPMS(Display Power Management Signaling) standard.

1.2GENERAL REQUIREMENTS

1.2.1Test Condition

Brightness level & contrast level max. Full white pattern test mode following spec. Warm up more than 1 hr, ambient light < 10 Lux , Luminance meter CA210 or BM7 or same equipment

1.2.2Test Equipment

The reference signal source is a calibrated Chroma 2237 video generator or higher. The use of other signal generators during qualification and production is acceptable provided the product complies with this specification.

1.3 ELECTRICAL

This section describes the electrical requirement of the monitor.

The LCD monitor consists of an interface board, a power board and inverter board, a function key board.

The interface board will house the flat panel control logic , brightness control logic, audio function control (option), key function control, DDC and DC to DC conversion to supply the appropriate power to the whole board and LCD flat panel , and transmitting LVDS signals into LCD flat panel module to drive the LCD display circuit .

The power board will support main power DC5V to interface board, and drive the two CCFLs (Cold Cathode Fluorescent Tube).

The interface board provides the power ON / OFF control over the power board.

Whole monitor to control the DPMS LED indicator to function key board.

MONITOR SPECIFICATIONS

 

ITEM

SPEC

 

 

 

 

Signal Input

 

Frequency

Analog:

(Analog)

 

 

H:31kHz~94kHz

 

 

 

V:50Hz~75Hz

 

 

 

 

 

 

Pixel clock

205MHz (Max)

 

 

 

 

 

 

Video Input

Analog 0.7Vp-p

 

 

 

 

 

 

Display Pixels

640 x 480 (VGA) ~ 1920 x 1080

 

 

 

 

 

 

Sync Signal

Separate SYNC for TTL (N or P)

 

 

 

 

Signal Input

 

Frequency

Digital:

(Digital)

 

 

H:31kHz~94kHz

 

 

 

V:50Hz~75Hz

 

 

Pixel clock

165MHz (Max)

 

 

 

 

 

 

Video Input

Analog 0.7Vp-p

 

 

 

Input Impedance 7

 

 

 

 

 

 

Display Pixels

640 x 480 (VGA) ~ 1920 x 1080

 

 

 

 

Connector

 

AC Input

AC100V ~ AC240V 10% 50/60Hz, 3 pin AC power cord

 

 

 

 

 

 

Input connector

D-SUB 15 pin, DVI-D & HDMI

 

 

 

 

 

 

Audio Jack (OPTIONAL)

Audio input 3.

 

 

 

 

Power Comsumption

 

AC in 100V~240V

Active 50W(non-USB)/60W(w/USB), power saving < 2W

 

 

 

 

User’s Control

 

Front

Input ,E-KEY, Auto Adjust ,Menu Adjust(-), Adjust(+),Power

 

 

 

 

 

 

OSD

Contrast, Brightness, Position, Clock, Phase, Analog/Digital,

 

 

 

Reset, Color, Language select, etc.

 

 

 

 

Pre-Defined Timing

 

Factory

13

 

 

 

 

 

 

User

9

 

 

 

 

Plug and Play

 

 

VESA DDC2Bi

 

 

 

 

Power Saving

 

 

VESA DPMS

 

 

Input Signal Counter Tolerance

H 1 kHz, ≦V 1 Hz

 

 

 

 

1.3.1Interface Connectors

1.3.1.1Power Connector and Cables

The AC input shall have an IEC/CEE-22 type male power receptacle for connection to mains power.

The power cord shall be with length of 1.8 0.005 meters.

1.3.1.2 Video Signal Connectors and Cable

The signal cable shall be 1.8 0.005 meters long. At the end of the cable shall be a molded-over, shielded, triple row, 15 position, D-subminiature connector. The CPU connection shall have captive screw locks, which will be adequate for hand tightening. The monitor connection may use small screws.

Image 3
Contents Service Go to cover Scope Video Signal Amplitudes Content Analog input VGA treats all timings as PC-timings Defects 5.1Visual Inspection Diameter, they must be at least 15mm apart Main OSD Menu OSD Volume management OSD Go to cover Exploded Diagram Packing Exploded Diagram Exploded Diagram Product Exploded Diagram Plug in parallel direction Angel 5 degrees S11 S17 S18 S21 Go to cover Open the carton with a proper tool S10 S17 S21 Does OSM display when you push Menu key Next Circuit section Printed wire broke between P301 pin2, R304 and I308 pin Troubleshooting Abnormal screen for VGA Go to cover Troubleshooting Abnormal OSM display adjust problem Troubleshooting Abnormal plug and play operation for VGA Go to cover Troubleshooting Troubleshooting Checking the resolution change IC movement Troubleshooting Checking the DC/DC converter circuit Firmware Upgrade Process Go to cover Ssmeans Samsung Panel Hdmi Transfer DVI Connection Hdmi Transfer DVI Connection Acer H233H Block digram PCB No P01 TO263 ACERLCDH233HSCHEMATICSINTERFACEBDVGA & DDC Input ACERLCDH233HSCHEMATICSINTERFACEDVI & DDC Interface HDMI19P Acer H233H NC/A-POINT 6PIN ACERLCDH233HSCHEMATICSOSD Keybd Ledorange Ledwhite Power Board TOP Silk ACERLCDH233HLAYOUTSINTERFACE Board 1234567