Acer RB23WABAS service manual Defects 5.1Visual Inspection

Page 7

6

ACER H233H

1. Product Specification (continued)

Go to cover page

1.3.8Display Communications Channel

The monitor assembly shall provide a display communications channel that conforms to VESA DDC2Bi hardware requirements. This configuration shall contain the 128-byte (HDMI 256-byte)EDID file as specified by VESA EDID standard. The monitor should not write to the EDID file for the first two minutes of operation following power-up UNLESS some action taken by the user or the host CPU forces the write (for instance, requesting the serial number via the OSD). Furthermore, it is recommended that CMOS switches be incorporated to isolate the DDC IC from outside connections while the EDID Fault Management is being updated. This is to prevent corruption of the data by attempts to read the data while it is being changed.

1.3.9Firmware Update Function (same ISP function) The update firmware need through from the D-Sub connector, use DDC I2C bus to do update firmware.

1.4.ELECTRICAL

1.4.1General Requirements

The panel used as the display device shall be an 1920x1080 resolution 23W, TFT LCD. This panel shall be approved for use in this monitor.

1.4.2. Panel Timings

The controller included with the monitor shall translate all video timings from the CPU that meet the timing requirements listed in Panel specification into timings appropriate for the panel. Under no circumstances may the controller supply the panel with timings that may result in damage . The controller shall insulate the panel from the CPU , so that the panel shall always be driven per it's own specification regardless of the timings being sent from the CPU.

1.4.3.Polarizer Hardness

The outer face of the front polarizer panel shall be covered with a coating with a # 3 hardness value .

1.4.4.Backlight Requirements

1.4.4.1General Requirements

The backlight assembly shall be designed to support field replacement at the customer site or authorized service center.The lamps shall have a continuous operating life of at least 50,000 hours at 25℃. The operating life is defined as having ended when the illumination of light has reached 50% of the initial value. The lamps shall extend a sufficient amount from the edge of the light guide that sputtering over the life of the lamps shall not cause degradation of the luminance uniformity (such as non-illuminated bands along the edges of the display).

1.4.4.2Lamps Startup Time

The backlight lamps shall start about 2 sec of the time the monitor power switch is pressed or the

monitor is restarted from a power - down mode . The starting time shall stay about 2 sec. for the minimum expected life of the lamps.

Test conditions are as follows :

 

Ambient Light ----------------------

< 1.0 lux

Temperature--------------------------

10℃

Inactive Time -----------------------

> 24 hours

1.4.5.Defects

 

1.4.5.1Visual Inspection

 

The LCD panel shall be inspected with all pixels set to white, black, red , green , and blue. The color variation, brightness variation , and overall appearance must not be perceived as poor quality

.Areas and / or parameters considered questionable shall be subjected to detailed measurements .

1.4.5.2 Display Degradation

Over the life of the product , variation of the parameters specified in Panel specification shall be maintained within reasonable limits. The panel must not exhibit any significant defects while in operation ( excluding the CCFL operation ).This does not in any way change the warranty given by the panel manufacturer .

1.4.5.3 Light Leakage

Except for the active display area , there shall be no light emission visible from any angle from any other part of the display . For this test , the ambient illumination must follow panel's specification.

Image 7
Contents Service Go to cover Scope Video Signal Amplitudes Content Analog input VGA treats all timings as PC-timings Defects 5.1Visual Inspection Diameter, they must be at least 15mm apart Main OSD Menu OSD Volume management OSD Go to cover Exploded Diagram Packing Exploded Diagram Exploded Diagram Product Exploded Diagram Plug in parallel direction Angel 5 degrees S11 S17 S18 S21 Go to cover Open the carton with a proper tool S10 S17 S21 Does OSM display when you push Menu key Next Circuit section Printed wire broke between P301 pin2, R304 and I308 pin Troubleshooting Abnormal screen for VGA Go to cover Troubleshooting Abnormal OSM display adjust problem Troubleshooting Abnormal plug and play operation for VGA Go to cover Troubleshooting Troubleshooting Checking the resolution change IC movement Troubleshooting Checking the DC/DC converter circuit Firmware Upgrade Process Go to cover Ssmeans Samsung Panel Hdmi Transfer DVI Connection Hdmi Transfer DVI Connection Acer H233H Block digram PCB No P01 TO263 ACERLCDH233HSCHEMATICSINTERFACEBDVGA & DDC Input ACERLCDH233HSCHEMATICSINTERFACEDVI & DDC Interface HDMI19P Acer H233H NC/A-POINT 6PIN ACERLCDH233HSCHEMATICSOSD Keybd Ledorange Ledwhite Power Board TOP Silk ACERLCDH233HLAYOUTSINTERFACE Board 1234567