BenQ MP727, MP735 user manual Connecting Component Video source devices

Page 25

Connecting Component Video source devices

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the D-SUB/COMP.INsocket on the projector.

The final connection path should be like that shown in the following diagram:

AV Device

English

Component Video to VGA (D-Sub) adaptor cable

Audio Cable

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made an HDMI Video connection between the projector and this Component Video source device using HDMI Video connections, you need not connect to this device using a Component Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 22 for details.

Connection 25

Image 25

Contents MP724/MP727/MP735 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Remote control Operating the Laser pointer Remote control effective range Choosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish MP724 MP724/727 projection dimensionsMP727 MP735 projection dimensions Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA to DVI-A cable Connecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to a DVI-I source device Connecting DVI-I source devicesTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesOperation Plug the power cord into the projectorStarting up the projector Using a security cable lock Using the menusUse / to highlight the System Setup Basic menu Leave and save the settingsSetting a password Utilizing the password functionTo leave the OSD menu, press MENU/EXIT Entering the password recall procedure If you forget the passwordChanging the password Enter the old passwordDisabling the password function Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityThen sharpen the image by rotating the Focus ring Magnifying and searching for details About the aspect ratio Selecting the aspect ratioMP735 MP724 and MP727Picture modes for different types of signals Selecting a picture modeOptimizing the image Fine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays 3D Color ManagementPress Its values to your preference by pressingTo cancel the timer, perform the following steps Setting the presentation timerGo to the System Setup Basic Presentation Timer menu and press ModeHiding the image Remote paging operationsVersion PictureLocking control keys Utilizing FAQ functionFreezing the image Creating your own startup screen Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Muting the soundShutting down the projector Personalizing the projector menu displayMenu system Menu operationBasic InformatiRing tone AdvancedDescription of each menu Temperature 3D Color Picture menu Source 4. System Setup menuBasic menuSave Settings TimerAuto Power System Setup Basic menuBlank Timer Sleep TimerReset All System Setup Advanced menuStandby D Sub OutputFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Do not turn the power on with the lamp cover removedTighten the screws that secure the lamp Settings page displays. Press to Setup Advanced Lamp SettingsMenu. Press MODE/ENTER. The Lamp Indicators Troubleshooting Projector specifications SpecificationsTiming chart Dimensions1280 x 62.8 74.9 106.5 49.7 59.8 83.571.554 84.880 122.500 640 x 480@67Hz 35.000 66.667 30.24015.63 PAL-60 15.73 NTSC4.43 15.63 25 or1280 x 79.976 75.025 135.000 63.981 60.020 108.00091.146 85.024 157.500 1024 x 768@75Hz 60.241 75.020 80.000Limited warranty Warranty and Copyright informationFCC statement Regulation statements