BenQ MP735, MP727 user manual Magnifying and searching for details

Page 36

English

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

Using the remote control

1.Press Zoom +/- to display the Zoom bar.

2. Press Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

4. To restore the picture to its original size, press AUTO. You can also press Zoom -. When the key is pressed again, the picture is further reduced until it is restored to the original size.

• Using the OSD menu

1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.

3.Repeat steps 2-4in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps.

4.Press on the projector repeatedly to magnify the picture to a desired size.

5.To navigate the picture, press MODE/ENTER to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture.

6.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out functionality, and press AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

36 Operation

Image 36
Contents Welcome MP724/MP727/MP735 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Remote control Operating the Laser pointer Remote control effective range Positioning your projector Choosing a locationObtaining a preferred projected image size Aspect display area Display areaEnglish MP724/727 projection dimensions MP724MP727 MP735 projection dimensions Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorWith a VGA to DVI-A cable Connecting Video source devices Connecting AudioBest video quality Better video qualityConnecting Hdmi source devices To connect the projector to an Hdmi source deviceConnecting DVI-I source devices To connect the projector to a DVI-I source deviceConnecting Component Video source devices To connect the projector to a Component Video source deviceConnecting S-Video source devices To connect the projector to an S-Video source deviceConnecting Composite Video source devices To connect the projector to a composite Video source devicePlug the power cord into the projector OperationStarting up the projector Using the menus Using a security cable lockUse / to highlight the System Setup Basic menu Leave and save the settingsUtilizing the password function Setting a passwordTo leave the OSD menu, press MENU/EXIT If you forget the password Entering the password recall procedureChanging the password Enter the old passwordDisabling the password function Switching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneThen sharpen the image by rotating the Focus ring Magnifying and searching for details Selecting the aspect ratio About the aspect ratioMP724 and MP727 MP735Selecting a picture mode Picture modes for different types of signalsOptimizing the image Using Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant Color3D Color Management Press MODE/ENTER and the 3D Color Management page displaysPress Its values to your preference by pressingSetting the presentation timer To cancel the timer, perform the following stepsGo to the System Setup Basic Presentation Timer menu and press ModeRemote paging operations Hiding the imageVersion PictureUtilizing FAQ function Locking control keysFreezing the image Operating in a high altitude environment Creating your own startup screenAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Muting the soundPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemInformati BasicAdvanced Ring toneDescription of each menu Picture menu Source 4. System Setup menuBasic menu Temperature 3D ColorSave Settings TimerSystem Setup Basic menu Auto PowerBlank Timer Sleep TimerSystem Setup Advanced menu Reset AllStandby D Sub OutputFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Do not turn the power on with the lamp cover removed Replacing the lampTighten the screws that secure the lamp Setup Advanced Lamp Settings Settings page displays. Press toMenu. Press MODE/ENTER. The Lamp Indicators Troubleshooting Specifications Projector specificationsDimensions Timing chart49.7 59.8 83.5 1280 x 62.8 74.9 106.571.554 84.880 122.500 640 x 480@67Hz 35.000 66.667 30.24015.63 25 or 15.63 PAL-60 15.73 NTSC4.4363.981 60.020 108.000 1280 x 79.976 75.025 135.00091.146 85.024 157.500 1024 x 768@75Hz 60.241 75.020 80.000Warranty and Copyright information Limited warrantyRegulation statements FCC statement