BenQ MP727 Setting the presentation timer, To cancel the timer, perform the following steps

Page 43
Are you sure to turn on the Presentation Timer?

Setting the presentation timer

The presentation timer can indicate the presentation

Presentation Timer

 

time on the screen to help you achieve better time

Timer period

15

management when giving presentations. Follow these

Timer display

Always

Timer position

Top-Left

steps to utilize this function:

Sound reminder

Off

 

Timer counting direction

Count Down

1. Go to the SYSTEM SETUP: Basic >

On

Off

Presentation Timer menu and press MODE/

 

MENU Back

ENTER to display the Presentation Timer

 

 

page.

 

 

2.Press to highlight Timer period and decide the timer period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the

period is reset.

3.Press to highlight Timer display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

Always

Displays the timer on screen throughout the presentation time.

 

 

1 min/2 min/3 min

Displays the timer on screen in the last 1/2/3 minute(s).

 

 

Never

Hides the timer throughout the presentation time.

 

 

English

4.Press to highlight Timer position and set the timer position by pressing / .

Top-Left Bottom-Left Top-Right Bottom- Right

5.Press to highlight Timer counting direction and select your desired counting direction by pressing / .

5 min

5 min

5 min

5 min

Selection

Description

Count Up

Increases from 0 to the preset time.

Count Down

Decrease from the preset time to 0.

6.Press to highlight Sound reminder to select On. A notice sound alerts 30 seconds before and at the end of the Presentation Timer countdown.

7.To activate the presentation timer, press and

press / to select On and press MODE/

ENTER.

8.A confirmation message displays. Highlight Yes

and press MODE/ENTER to confirm. You will

Yes

No

see the message “Timer is On” displaying on the

 

 

screen. The timer starts counting at the time the

 

 

timer is on.

 

 

To cancel the timer, perform the following steps.

1.Go back to the Presentation Timer page.

2.Press and press / to highlight Off and press MODE/ENTER. A confirmation message displays.

Operation 43

Image 43
Contents MP724/MP727/MP735 Digital Projector WelcomeTable of contents Lens during operation. The intense Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Remote control Operating the Laser pointer Remote control effective range Choosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish MP724 MP724/727 projection dimensionsMP727 MP735 projection dimensions To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionTo connect the projector to a monitor Connecting a monitorWith a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to a DVI-I source device Connecting DVI-I source devicesTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesOperation Plug the power cord into the projectorStarting up the projector Leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup Basic menuSetting a password Utilizing the password functionTo leave the OSD menu, press MENU/EXIT Enter the old password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityThen sharpen the image by rotating the Focus ring Magnifying and searching for details About the aspect ratio Selecting the aspect ratioMP735 MP724 and MP727Picture modes for different types of signals Selecting a picture modeOptimizing the image Adjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessIts values to your preference by pressing 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays PressPresentation Timer menu and press Mode Setting the presentation timerTo cancel the timer, perform the following steps Go to the System Setup BasicPicture Remote paging operationsHiding the image VersionLocking control keys Utilizing FAQ functionFreezing the image Creating your own startup screen Operating in a high altitude environmentMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneShutting down the projector Personalizing the projector menu displayMenu system Menu operationBasic InformatiRing tone AdvancedDescription of each menu Timer Picture menu Source 4. System Setup menuBasic menuTemperature 3D Color Save SettingsSleep Timer System Setup Basic menuAuto Power Blank TimerSub Output System Setup Advanced menuReset All Standby DCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationTiming of replacing the lamp Replacing the lamp Do not turn the power on with the lamp cover removedTighten the screws that secure the lamp Settings page displays. Press to Setup Advanced Lamp SettingsMenu. Press MODE/ENTER. The Lamp Indicators Troubleshooting Projector specifications SpecificationsTiming chart Dimensions640 x 480@67Hz 35.000 66.667 30.240 49.7 59.8 83.51280 x 62.8 74.9 106.5 71.554 84.880 122.50015.63 PAL-60 15.73 NTSC4.43 15.63 25 or1024 x 768@75Hz 60.241 75.020 80.000 63.981 60.020 108.0001280 x 79.976 75.025 135.000 91.146 85.024 157.500Limited warranty Warranty and Copyright informationFCC statement Regulation statements