BenQ MP727, MP735 user manual Advanced, Ring tone

Page 51
Baud Rate
Test Pattern
Reset All Settings

 

Quick Cooling

 

Off/On

 

 

 

 

High Altitude Mode

Off/On

 

 

 

 

 

Audio Settings

Mute

Off/On

 

 

Volume

Range : 0 ~ 10

 

 

Power on/off

Off/On

 

 

ring tone

 

 

 

 

 

 

 

Menu display

5 sec/10 sec/15 sec/20 sec/

 

Menu Settings

time

25 sec/30 sec

 

 

 

 

Menu position

Center/Top-left/Top-right/Bottom-

 

 

 

 

right/Bottom-left

 

 

 

5.

 

 

Standby D-Sub Output

Off/On

SYSTEM

 

 

 

 

Lamp Mode

Normal/Economic

SETUP:

Lamp Settings

 

 

Reset lamp timer

 

Advanced

 

 

 

 

Equivalent Lamp Hour

 

 

 

 

 

 

 

 

Change password

 

 

 

 

 

Security

Change Security Settings

 

 

 

 

Power on Lock

Off/On

 

Settings

 

 

 

Splash Screen

Off/On

Lock

 

2400/4800/9600/14400/19200/ 38400/57600/115200

Off/On

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

The default values listed in this manual, especially on page 49-56, are for reference only. They may vary from the projectors due to the continuous improvement to the products.

English

Operation 51

Image 51
Contents MP724/MP727/MP735 Digital Projector WelcomeTable of contents Lens during operation. The intense Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Remote control Operating the Laser pointer Remote control effective range Choosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish MP724 MP724/727 projection dimensionsMP727 MP735 projection dimensions To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor To connect the projector to a monitorWith a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to a DVI-I source device Connecting DVI-I source devicesTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesPlug the power cord into the projector OperationStarting up the projector Leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordTo leave the OSD menu, press MENU/EXIT Enter the old password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneThen sharpen the image by rotating the Focus ring Magnifying and searching for details About the aspect ratio Selecting the aspect ratioMP735 MP724 and MP727Selecting a picture mode Picture modes for different types of signalsOptimizing the image Adjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessIts values to your preference by pressing 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays PressPresentation Timer menu and press Mode Setting the presentation timerTo cancel the timer, perform the following steps Go to the System Setup BasicPicture Remote paging operationsHiding the image VersionUtilizing FAQ function Locking control keysFreezing the image Creating your own startup screen Operating in a high altitude environmentMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneShutting down the projector Personalizing the projector menu displayMenu system Menu operationBasic InformatiRing tone AdvancedDescription of each menu Timer Picture menu Source 4. System Setup menuBasic menuTemperature 3D Color Save SettingsSleep Timer System Setup Basic menuAuto Power Blank TimerSub Output System Setup Advanced menuReset All Standby DCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationTiming of replacing the lamp Replacing the lamp Do not turn the power on with the lamp cover removedTighten the screws that secure the lamp Setup Advanced Lamp Settings Settings page displays. Press toMenu. Press MODE/ENTER. The Lamp Indicators Troubleshooting Projector specifications SpecificationsTiming chart Dimensions640 x 480@67Hz 35.000 66.667 30.240 49.7 59.8 83.51280 x 62.8 74.9 106.5 71.554 84.880 122.50015.63 PAL-60 15.73 NTSC4.43 15.63 25 or1024 x 768@75Hz 60.241 75.020 80.000 63.981 60.020 108.0001280 x 79.976 75.025 135.000 91.146 85.024 157.500Limited warranty Warranty and Copyright informationFCC statement Regulation statements