BenQ MP776 ST user manual Connecting video source devices, Connecting audio

Page 20

Connecting video source devices

You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Terminal

Terminal appearance Reference

Picture quality

name

 

 

HDMI

"Connecting an HDMI

Best

device" on page 21

 

 

Component

"Connecting a Component

 

Video source device" on

Better

Video

page 21

 

 

 

S-Video

"Connecting an S-Video/

Good

 

 

 

Composite Video source

 

 

device" on page 22

 

Video

 

Normal

Connecting audio

The projector has two built-in mono speakers which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speakers.

If you have a separate sound system, you will most likely want to connect the audio output of your video source device to that sound system, instead of to the mono audio projector. The audio connections illustrated on page 18 are provided for informational purposes only. You need not connect audio to the projector if there is an alternate sound system available, or if audio is not required.

20 Connection

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Welcome MP772 ST/MP776 ST Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewFront/upper side Rear/lower side Controls and functions ProjectorRemote control Keystone/Arrow buttons / Up Auto ModeOperating the Laser pointer Approx.+15 Remote control effective rangeReplacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingObtaining a preferred projected image size Page Projection dimensions Vertical offsetConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioConnecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceOperation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Press Menu/Exit on the projector or remoteUsing a security cable lock Utilizing the password functionSetting a password To the Security SettingsChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Correcting keystoneSwitching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperatureAbout color temperatures 3D Color ManagementSetting the presentation timer Selection DescriptionTo cancel the timer, perform the following steps How to use the Timer On key?Using the remote control Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Hiding the imageLocking control keys Utilizing FAQ functionGo to the System Setup Basic Panel Key Lock Adjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Operating in a high altitude environmentConfiguring the Lan Control Settings Personalizing the projector menu displayControlling the projector through a Lan environment If you are in a Dhcp environmentControlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options BasicAdvanced Closed Caption On/Off Enable Caption Version Control By RJ45/RS232Projector IP Lan Control AddressDescription of each menu Picture Mode TemperatureSave Settings ReferenceTimer SettingsAuto Power Blank TimerSettings Security QuickAudio StandbyReset All ClosedCaption Lan ControlFAQ-Image InstallationFeatures ServiceMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Tighten the screws that secure the lamp cover Connect the power and restart the projectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC input MP772 STSupported timing for PC input MP776 ST Supported timing for Hdmi Hdcp input MP776 ST SXGA85Signal Format Supported timing for Component-YPbPrinput MP772 ST/ MP776 STWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive
Top Page Image Contents