BenQ MP776 ST user manual Connecting an S-Video/Composite Video source device

Page 22

Connecting an S-Video/Composite Video source device

Examine your video source device to determine if it has an unused S-Video/Video output jack available:

•If it has both jacks, use the S-Video output jack for connection as the S-Video terminal provides better picture quality than the Video terminal.

•If it has either of the output jack, you can also continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video/Video source device:

1.Take an S-Video/Video cable and connect one end to the S-Video/Videooutput jack of the Video source device.

2.Connect the other end of the S-Video/Video cable to the S-VIDEO/VIDEOjack on the projector.

3.If you wish to make use of the projector (mixed mono) speakers in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO or AUDIO (L/R) jack of the projector.

4.If you wish and the AUDIO OUT jack is available on your projector, you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 50 for details.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 20 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

Contents Welcome MP772 ST/MP776 ST Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewLamp cover External control panel Controls and functions ProjectorRemote control Operating the Laser pointer Auto ModeKeystone/Arrow buttons / Up Replacing the remote control batteries Remote control effective rangeApprox.+15 Front Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Page Projection dimensions Vertical offsetConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioTo connect the projector to an Hdmi device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceStarting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Press Menu/Exit on the projector or remoteSetting a password Using a security cable lockUtilizing the password function To the Security SettingsEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Correcting keystoneSwitching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Brilliant ColorSelecting a color temperature 3D Color ManagementSetting the presentation timer Selection DescriptionUsing the remote control To cancel the timer, perform the following stepsHow to use the Timer On key? Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Hiding the imageGo to the System Setup Basic Panel Key Lock Utilizing FAQ functionLocking control keys Turning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Operating in a high altitude environmentControlling the projector through a Lan environment Configuring the Lan Control SettingsPersonalizing the projector menu display If you are in a Dhcp environmentControlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Projector IP Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Lan Control AddressDescription of each menu Save Settings Picture ModeTemperature ReferenceAuto Power TimerSettings Blank TimerAudio Settings SecurityQuick StandbyCaption Reset AllClosed Lan ControlFeatures FAQ-ImageInstallation ServiceMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screws that secure the lamp cover Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC input MP772 STSupported timing for PC input MP776 ST Supported timing for Hdmi Hdcp input MP776 ST SXGA85Signal Format Supported timing for Component-YPbPrinput MP772 ST/ MP776 STCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive