BenQ MP776 ST user manual Closed, Caption, Lan Control, Reset All

Page 51

Function

(default setting / value)

	5.	Closed
	SYSTEMSETUP:	Closed
	SYSTEMSETUP:	Caption
		Caption
	Advancedmenu	Lan Control
		Lan Control
		Settings
		Reset All
		Settings

Description

Closed Caption Enable (Off)

Activates the function by selecting On when the selected input signal carries closed captions.

•Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings).

Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is “16:9” or “Real”.

Caption Version (CC1)

Selects a preferred closed captioning mode. To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).

Control By (RS232)

DHCP (On)

Projector IP Address

Subnet Mask

Default Gateway

DNS Server

Apply

See "Controlling the projector through a Lan environment" on page 40 for details.

Returns all settings to the factory preset values.

The following settings will still remain: Position, Phase, H. Size, User 1, User 2, Color Space Conversion, Language, Projector Position, High Altitude Mode, Security Settings and Baud Rate.

Operation 51

Image 51

Contents MP772 ST/MP776 ST Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover External control panel Projector Controls and functionsRemote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Vertical offset Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceOperation Starting up the projectorOperation Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imagePress Menu/Exit on the projector or remote Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menuTo the Security Settings Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Correcting keystone Disabling the password functionChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature About color temperaturesSelection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsHow to use the Timer On key? Using the remote controlHiding the image Freezing the imageUtilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environment Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneIf you are in a Dhcp environment Configuring the Lan Control SettingsPersonalizing the projector menu display Controlling the projector through a Lan environmentIf you are in a non-DHCP environment Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Shutting down the projector Once the cooling process finishes, a Power Off RingBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Lan Control Address Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Projector IPDescription of each menu Reference Picture ModeTemperature Save SettingsBlank Timer TimerSettings Auto PowerStandby Settings SecurityQuick AudioLan Control Reset AllClosed CaptionService FAQ-ImageInstallation FeaturesCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input MP772 ST Timing chartSupported timing for PC input MP776 ST SXGA85 Supported timing for Hdmi Hdcp input MP776 STSupported timing for Component-YPbPrinput MP772 ST/ MP776 ST Signal FormatDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement