BenQ MP777 To cancel the timer, perform the following steps, How to use the Timer On key?

Page 36

4.Press to highlight Timer Position and set the timer position by pressing / .

Top-Left Bottom-Left Top-Right Bottom-Right

5.Press to highlight Timer Counting Direction and select your desired counting direction by pressing / .

Selection

Description

Count Up

Increases from 0 to the preset time.

Count Down

Decreases from the preset time to 0.

6.Press to highlight Sound Reminder and decide if you want to activate sound reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

7.To activate the presentation timer, press and press / to highlight On and press

MODE/ENTER.

8.A confirmation message displays. Highlight Yes and press MODE/ENTER on the projector or remote control to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting when the timer is on.

To cancel the timer, perform the following steps:

Using the remote control

Press Timer On and press / to highlight Off and press MODE/ENTER.

Using the OSD menu

1.Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press MODE/ENTER. A confirmation message displays.

2.Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off” displaying on the screen.

How to use the Timer On key?

Timer On is a multi-functional key.

• If the presentation timer is off, pressing this key displays a confirmation message. You can decide whether to activate the timer or not by following the on-screen instruction.

• If the timer is already on, pressing this key displays a confirmation message. You can decide whether to restart, continue or turn off the timer by following the on-screen instruction.

36 Operation

Image 36
Contents Welcome MP776/MP777 Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideExternal control panel Speaker grill IntroductionProjector Remote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Positioning your projector Choosing a locationFront Table Front CeilingObtaining a preferred projected image size Page Projection dimensions Screen size Distance from screen mm DiagonalVertical InchConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioConnecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorTo turn of the ring tone, see Turning off OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password To the Security SettingsIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneBottom of the image Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperatureAbout color temperatures 3D Color ManagementSetting the presentation timer Selection DescriptionTo cancel the timer, perform the following steps How to use the Timer On key?Using the remote control Top-Left Bottom-Left Top-Right Bottom-RightUtilizing FAQ function Freezing the imageHiding the image To exit the OSD menu, press MENU/EXIT OperationGo to the System Setup Basic Panel Key Lock To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Personalizing the projector menu displayConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi. To switch input source, click on your desired signal Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options BasicAdvanced Closed Caption On/Off Enable Caption Version Control By RJ45/RS232Projector IP Lan Control AddressDescription of each menu Color Temperature Save SettingsTimer Color Tint SharpnessSettings Auto PowerProjector MenuLamp SecurityTest Pattern Baud RateReset All FAQ-ImageInstallation FeaturesMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input MP776 SXGA85Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive