BenQ MP777 user manual Press Exit to go back to the remote network operation

Page 42

The tools page allows you to manage the projector, configure the Lan control settings and secure access of remote network operation on this projector.

iiii

iiiv

v

i.You can name the projector, keep track of its location and the person in charge of it.

ii.You can adjust the Lan Control Settings.

iii.Once set, access to the remote network operation on this projector has been password-protected.

iv.Once set, access to the tools page has been password-protected.

After making the adjustments, press the Send button and the data will be saved in the projector.

v.Press Exit to go back to the remote network operation page. The info page displays the information and status of this projector.

Press Exit to go back to the remote network operation page.

For more information, visit http://www.crestron.com. If you are an IT administrator and would like to manage multiple devices through one interface, you can download Crestron Roomview at www.crestron.com/getroomview.

42 Operation

Image 42
Contents Welcome MP776/MP777 Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents External control panel Projector exterior viewFront/upper side Speaker grill IntroductionProjector Remote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Front Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Page Vertical Projection dimensionsScreen size Distance from screen mm Diagonal InchConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioTo connect the projector to an Hdmi device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceTo turn of the ring tone, see Turning off OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function To the Security SettingsIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneBottom of the image Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Brilliant ColorSelecting a color temperature 3D Color ManagementSetting the presentation timer Selection DescriptionUsing the remote control To cancel the timer, perform the following stepsHow to use the Timer On key? Top-Left Bottom-Left Top-Right Bottom-RightHiding the image Utilizing FAQ functionFreezing the image To exit the OSD menu, press MENU/EXIT OperationLocking control keys Go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Personalizing the projector menu displayIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environmentIi. To switch input source, click on your desired signal Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Projector IP Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Lan Control AddressDescription of each menu Timer Color TemperatureSave Settings Color Tint SharpnessProjector SettingsAuto Power MenuTest Pattern LampSecurity Baud RateInstallation Reset AllFAQ-Image FeaturesMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input MP776 SXGA85Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive