BenQ MP777 user manual Projector exterior view, Front/upper side, External control panel

Page 9

Projector exterior view

Front/upper side

1								6
1
2
3								7
								8
4
								9
5
Rear/lower side
14	15	16	17	18	19	20	21	22
10
11

4				24

1.External control panel

(See "Controls and functions" on page 10 for details.)

2.Lamp cover

3.Vent (heated air exhaust)

4.Quick-release button

5.Lens cover

6.Focus ring and Zoom ring

7.Vent (cool air intake)

8.Front IR remote sensor

9.Projection lens

10.AC power jack

11.Kensington anti-theft lock slot

12.Rear adjuster foot

13.Ceiling mount holes

14.Rear IR remote sensor

15.RJ45 LAN input jack

16.RS232 control port

17.RGB signal output jack

18.HDMI-input port

19.RGB (PC)/Component Video (YPbPr/ YCbCr) signal input jack

20.S-Video input jack Video input jack

21.Audio (L/R) input jacks

22.Audio input jack Audio output jack

23.12V DC output terminal

Used to trigger external devices such as an electric screen or light control, etc. Consult your dealer for how to connect these devices.

24.Speaker grill

Introduction 9

Image 9

Contents MP776/MP777 Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Front/upper side Projector exterior viewExternal control panel Speaker grill IntroductionProjector Remote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Page Screen size Distance from screen mm Diagonal Projection dimensionsVertical InchConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting video source devicesConnecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceStarting up the projector OperationTo turn of the ring tone, see Turning off OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password To the Security SettingsIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneBottom of the image Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant ColorAbout color temperatures 3D Color ManagementSelection Description Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsUsing the remote control Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionHiding the image To exit the OSD menu, press MENU/EXIT OperationTo activate the High Altitude Mode Go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Personalizing the projector menu displayControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Ii. To switch input source, click on your desired signalPress Exit to go back to the remote network operation Shutting down the projector Once the cooling process finishes, a Power Off RingMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Control By RJ45/RS232 Closed Caption On/Off Enable Caption VersionProjector IP Lan Control AddressDescription of each menu Save Settings Color TemperatureTimer Color Tint SharpnessAuto Power SettingsProjector MenuSecurity LampTest Pattern Baud RateFAQ-Image Reset AllInstallation FeaturesCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSXGA85 Supported timing for Hdmi Hdcp input MP776Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive