BenQ MP777 Lan Control, Reset All, FAQ-Image, Installation, Features, Service, Current, Status

Page 51

Function

(default setting / value)

	5.
	SYSTEM	Settings
		Lan Control
	SETUP:
	Advanced	Reset All
		Reset All
	menu	Settings
	menu
		FAQ-Image
		and
		Installation

		FAQ-
	6	Features and
	.	Service
	INFORMATION	Current
	menu	Current
	menu	Status
		System

Description

Control By (RS232)

DHCP (On)

Projector IP Address

Subnet Mask

Default Gateway

DNS Server

Apply

See "Controlling the projector through a Lan environment" on page 40 for details.

Returns all settings to the factory preset values.

The following settings will still remain: Position, Phase, H. Size, User 1, User 2, Color Space Conversion, Language, Projector Position, High Altitude Mode, Security Settings and Baud Rate.

Displays possible solutions to problems you may encounter.

Source

Shows the current signal source.

Picture Mode

Shows the selected mode in the PICTURE menu.

Resolution

Shows the native resolution of the input signal.

Color System

Shows input system format: NTSC, PAL, SECAM, or RGB.

Equivalent Lamp Hour

Displays the number of hours the lamp has been used.

Firmware Version

Shows the firmware version of your projector.

Operation 51

Image 51

Contents MP776/MP777 Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Speaker grill Introduction Projector exterior viewFront/upper side External control panelProjector Remote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Inch Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceOperation OperationStarting up the projector To turn of the ring tone, see Turning offFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu To the Security Settings Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneBottom of the image Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature About color temperaturesSelection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsHow to use the Timer On key? Using the remote controlTo exit the OSD menu, press MENU/EXIT Operation Utilizing FAQ functionFreezing the image Hiding the imageOperating in a high altitude environment Go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Locking control keysPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneIf you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentControlling the projector remotely through a web browser Ii. To switch input source, click on your desired signalPress Exit to go back to the remote network operation Shutting down the projector Once the cooling process finishes, a Power Off RingBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Lan Control Address Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Projector IPDescription of each menu Color Tint Sharpness Color TemperatureSave Settings TimerMenu SettingsAuto Power ProjectorBaud Rate LampSecurity Test PatternFeatures Reset AllFAQ-Image InstallationCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSXGA85 Supported timing for Hdmi Hdcp input MP776Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement