BenQ MP777 Confined. Allow at least 50 cm clearance, If the ventilation holes are seriously

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the 14. Do not block the ventilation holes.

following environments.

- Do not place this projector on a blanket,

- Space that is poorly ventilated or

bedding or any other soft surface.

- Do not cover this projector with a cloth

confined. Allow at least 50 cm clearance

from walls and free flow of air around

or any other item.

the projector.

- Do not place inflammables near the

- Locations where temperatures may

projector.

become excessively high, such as the

 

inside of a car with all windows rolled

 

up.

 

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

 

If the ventilation holes are seriously

 

obstructed, overheating inside the

 

projector may result in a fire.

15.

Always place the projector on a level,

 

horizontal surface during operation.

 

- Do not use if tilted at an angle of more

- Locations near fire alarms

than 10 degrees left to right, nor at angle

- Locations with an ambient temperature

of more than 15 degrees front to back.

Using the projector when it is not fully

above 40°C / 104°F

horizontal may cause a malfunction of,

- Locations where the altitudes are higher

or damage to, the lamp.

than 3000 m (10000 feet).

 

3000 m

(10000 feet)

16.

Do not stand the projector on end

0 m

vertically. Doing so may cause the

projector to fall over, causing injury or

(0 feet)

 

 

 

 

 

 

resulting in damage to the projector.

Important safety instructions

5

Image 5
Contents MP776/MP777 Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewExternal control panel Speaker grill IntroductionProjector Remote control Keystone/Arrow buttons / Up Auto ModeOperating the Laser pointer Approx.+15 Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Page Screen size Distance from screen mm Diagonal Projection dimensionsVertical InchConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting video source devicesConnecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceStarting up the projector OperationTo turn of the ring tone, see Turning off OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password To the Security SettingsChanging the password If you forget the passwordEntering the password recall procedure Bottom of the image Operation Disabling the password functionCorrecting keystone Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant ColorAbout color temperatures 3D Color ManagementSelection Description Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsUsing the remote control Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionHiding the image To exit the OSD menu, press MENU/EXIT OperationTo activate the High Altitude Mode Go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Personalizing the projector menu displayControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Ii. To switch input source, click on your desired signalPress Exit to go back to the remote network operation Shutting down the projector Once the cooling process finishes, a Power Off RingMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Control By RJ45/RS232 Closed Caption On/Off Enable Caption VersionProjector IP Lan Control AddressDescription of each menu Save Settings Color TemperatureTimer Color Tint SharpnessAuto Power SettingsProjector MenuSecurity LampTest Pattern Baud RateFAQ-Image Reset AllInstallation FeaturesCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Tighten the screws that secure the lamp cover Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSXGA85 Supported timing for Hdmi Hdcp input MP776Supported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive