BenQ MP777 user manual Lamp, Security, Test Pattern, Baud Rate, Closed, Caption

Page 50

Function

(default setting / value)

Standby Monitor Out (Off)

		Lamp
	5. SYSTEM	Settings
	5. SYSTEM	Security
	SETUP:	Security
	SETUP:	Settings
	Advanced	Settings
	Advanced	Test Pattern
		Baud Rate
		(115200)
	menu	(Off)
	menu
		Closed
		Caption

Description

Selecting On enables the function. The projector can output a VGA signal when it is in standby mode and the COMPUTER 1 jack is correctly connected to devices. See "Connecting a monitor" on page 19 for how to make the connection.

Enabling this function slightly increases the standby power consumption.

Lamp Mode (Normal)

See "Setting Lamp Mode as Economic" on page 53 for details.

Reset lamp timer

See "Resetting the lamp timer" on page 57 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 53 for details on how the total lamp hour is calculated.

Change Password

You will be asked to enter the current password before changing to a new one. See "Utilizing the password function" on page 26 for details.

Power On Lock (Off)

See "Utilizing the password function" on page 26 for details.

Selects a baud rate that is identical with your computer’s so that you can connect the projector using a suitable RS-232 cable and update or download the projector’s firmware. This function is intended for qualified service personnel.

Selecting On enables the function and the projector displays the grid test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion.

Closed Caption Enable (Off)

Activates the function by selecting On when the selected input signal carries closed captions.

•Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings).

Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is “16:9” or “Real”.

Caption Version (CC1)

Selects a preferred closed captioning mode. To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).

50 Operation

Image 50

Contents Welcome MP776/MP777 Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents External control panel Projector exterior viewFront/upper side Speaker grill IntroductionProjector Remote control Keystone/Arrow buttons / Up Auto ModeOperating the Laser pointer Approx.+15 Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Page Vertical Projection dimensionsScreen size Distance from screen mm Diagonal InchConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioTo connect the projector to an Hdmi device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceTo turn of the ring tone, see Turning off OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function To the Security SettingsChanging the password If you forget the passwordEntering the password recall procedure Bottom of the image Operation Disabling the password functionCorrecting keystone Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Brilliant ColorSelecting a color temperature 3D Color ManagementSetting the presentation timer Selection DescriptionUsing the remote control To cancel the timer, perform the following stepsHow to use the Timer On key? Top-Left Bottom-Left Top-Right Bottom-RightHiding the image Utilizing FAQ functionFreezing the image To exit the OSD menu, press MENU/EXIT OperationLocking control keys Go to the System Setup Basic Panel Key LockTo activate the High Altitude Mode Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Personalizing the projector menu displayIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environmentIi. To switch input source, click on your desired signal Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Projector IP Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Lan Control AddressDescription of each menu Timer Color TemperatureSave Settings Color Tint SharpnessProjector SettingsAuto Power MenuTest Pattern LampSecurity Baud RateInstallation Reset AllFAQ-Image FeaturesMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Tighten the screws that secure the lamp cover Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input MP776 SXGA85Supported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive