BenQ MP625P user manual Entering the password recall procedure, Changing the password

Page 29

password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 29 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1.Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > Change password menu.

2.Press Mode/Enter. The message 'INPUT CURRENT PASSWORD' displays.

3.Enter the old password.

•If the password is correct, another message 'INPUT NEW PASSWORD' displays.

•If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry. You can press Menu/Exit to cancel the change or try another password.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press Menu/Exit.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock menu after opening the OSD menu system. Select Off by pressing

/ . The message 'INPUT PASSWORD' displays. Enter the current password.

•If the password is correct, the OSD menu returns to the Security Settings page with 'Off' shown in the row of Power on lock. You will not have to enter the password next time you turn on the projector.

Operation 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MP615P/MP625P Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewControls and functions Projector Ceiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source device MP625P onlyTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUsing the menus Utilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Operation Changing Color Space MP625P only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorPress Mode/Enter and the 3D Color Management page displays About color temperatures3D Color Management Operation To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHiding the image How to use the Timer On key?Remote paging operations Freezing the image Utilizing FAQ functionAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Picture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuSettings TimerAuto Power Blank TimerQuick System Setup Advanced menuCooling High AltitudeReset All Direct powerClosed CaptionFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements
Top Page Image Contents