BenQ MP625P Picture menu, Picture Mode, Reference, Brightness, Contrast, Color, Tint, Sharpness

Page 47

2. PICTURE menu

FUNCTION

DESCRIPTION (default setting/value)

(default setting/

value)

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 34 for details.

 

 

 

Selects a picture mode that best suits your need for the image quality

Reference

and further fine-tune the image based on the selections listed on the

same page below. See "Setting the User 1/User 2 mode" on page 34 for

Mode

details.

 

This function is only available when User 1/2 is selected.

 

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 35 for details.

 

This function is only available when User 1/2 is selected.

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 35 for details.

 

This function is only available when User 1/2 is selected.

 

 

 

Adjusts the color saturation level -- the amount of each color in a

Color

video image. See "Adjusting Color" on page 35 for details.

This function is only available when User 1/2 is selected.

 

 

This function is only available when a Video or S-Video signal is

 

selected and the system format is NTSC or PAL.

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 35 for details.

This function is only available when User 1/2 is selected.

 

 

This function is only available when a Video or S-Video signal is

 

selected and the system format is NTSC or PAL..

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 35 for details.

This function is only available when User 1/2 is selected.

 

 

This function is only available when a Video or S-Video signal is

 

selected and the system format is NTSC or PAL.

Operation 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents MP615P/MP625P Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewControls and functions Projector Ceiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source device MP625P onlyTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUsing the menus If you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Operation Changing Color Space MP625P only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorPress Mode/Enter and the 3D Color Management page displays About color temperatures3D Color Management Operation Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Presentation TimerHiding the image How to use the Timer On key?Remote paging operations Freezing the image Utilizing FAQ functionOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Mode Picture ModePicture menu ReferencePicture menu Source menu TemperatureSave Settings Input signalBlank Timer TimerSettings Auto PowerHigh Altitude System Setup Advanced menuQuick CoolingCaption Direct powerReset All ClosedCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsUnit mm DimensionsCeiling mount installation Ceiling mount screwsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements
Top Page Image Contents