BenQ MP625P user manual Closed, Caption, Standby, Monitor Out, Direct power, Reset All

Page 51

5. SYSTEM SETUP: Advanced menu

FUNCTION
(default setting/ DESCRIPTION (default setting/value)
value)
	Closed Caption Enable
	Activates the function by selecting On when the selected input signal
	carries closed captions.
Closed	• Captions: An on-screen display of the dialogue, narration, and
Closed	sound effects of TV programs and videos that are closed captioned
Caption	(usually marked as "CC" in TV listings).
	Set your screen aspect ratio to 4:3. This function is not available
	when the aspect ratio is “16:9” or “Real”.

		Caption Version
		Selects a preferred closed captioning mode.

		Selecting On enables the function. The projector can output a VGA
		signal when it is in standby mode and the COMPUTER 1 and
	Standby	MONITOR OUT jacks are correctly connected to devices. See
		"Connecting a monitor" on page 19 for how to make the connection.

	Monitor Out	Enabling this function slightly increases the standby power
		consumption.
		The Standby Monitor Out only works when an appropriate D-
		Sub input is made to the COMPUTER 1 jack.
	Direct power	Selecting On enables the function. See "Starting up the projector" on
	Direct power	page 24 for details.
	on	page 24 for details.
	on

	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Position, Phase, H. Size,
	Settings
	Settings	User 1, User 2, Language, Projector Position, High Altitude
		Mode, Security Settings, Baud Rate.

Operation 51

Image 51

Contents MP615P/MP625P Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewControls and functions Projector Ceiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source device MP625P onlyTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUsing the menus If you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Operation Changing Color Space MP625P only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Operation Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Presentation TimerHow to use the Timer On key? Remote paging operationsHiding the image Freezing the image Utilizing FAQ functionOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Mode Picture ModePicture menu ReferencePicture menu Source menu TemperatureSave Settings Input signalBlank Timer TimerSettings Auto PowerHigh Altitude System Setup Advanced menuQuick CoolingCaption Direct powerReset All ClosedCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsUnit mm DimensionsCeiling mount installation Ceiling mount screwsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements