BenQ MP625P user manual Specifications, Optical

Page 61

Specifications

All specifications are subject to change without notice.

Optical

Resolution (MP625P)

1024 x 768 XGA

(MP615P)

800 x 600 SVGA

Display system 1-CHIP DMD

Lens F/Number

F = 2.51 to 2.69,

f = 21.95 to 24.18 mm

Lamp

185 W lamp

Electrical

Power supply AC100–240V, 2.9 A, 50-60 Hz (Automatic)

Power consumption

260 W (Max); < 1 W (Standby)

Control

RS-232 serial control 9 pin x 1

IR receiver x 1 USB Type B x 1

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

(MP625P) Digital-HDMI x 1

Audio signal input Audio in

PC audio jack x 1

Mechanical

Weight

5.5 lbs (2.5 Kg)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 2 watt x 1 Audio signal output

PC audio jack x 1

Environmental Requirements

Operating temperature 0°C°-40°C at sea level

Operating relative humidity 10%-90% (without condensation)

Operating altitude 0-1499 m at 0°C°-35°C

1500-3000 m at 0°C-30°C (with High Altitude Mode on)

Specifications 61

Image 61

Contents MP615P/MP625P Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewControls and functions Projector Ceiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source device MP625P onlyTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUsing the menus Utilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Operation Changing Color Space MP625P only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall Color3D Color Management About color temperaturesPress Mode/Enter and the 3D Color Management page displays Operation To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations How to use the Timer On key?Hiding the image Freezing the image Utilizing FAQ functionAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Picture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuSettings TimerAuto Power Blank TimerQuick System Setup Advanced menuCooling High AltitudeReset All Direct powerClosed CaptionFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements