BenQ MP610 user manual Troubleshooting, Cause Remedy, Plug the power cord into the AC inlet on

Page 50

Troubleshooting

THE PROJECTOR DOES NOT TURN ON.

Cause

Remedy

 

 

 

Plug the power cord into the AC inlet on the

There is no power from the power

projector, and plug the power cord into the

cable.

power outlet. If the power outlet has a switch,

 

make sure that it is switched on.

 

 

Attempting to turn the projector on

Wait until the cooling down process has

again during the cooling process.

completed.

 

 

NO PICTURE

Cause

Remedy

 

 

The video source is not turned on or

Turn the video source on and check that the

connected correctly.

signal cable is connected correctly.

 

 

The projector is not correctly

Check the connection.

connected to the input source device.

 

 

 

The input signal has not been

Select the correct input signal with the Source

correctly selected.

key on the projector or remote control.

 

 

The lens cap is still attached to the

Remove the lens cap.

lens.

 

 

 

BLURRED IMAGE

Cause

Remedy

 

 

The projection lens is not correctly

Adjust the focus of the lens using the focus

focused.

ring.

 

 

The projector and the screen are not

Adjust the projection angle and direction as

aligned properly.

well as the height of the unit if necessary.

 

 

The lens cap is still attached to the

Remove the lens cap.

lens.

 

 

 

REMOTE CONTROL DOES NOT WORK

Cause

Remedy

 

 

The battery is out of power.

Replace the battery with a new one.

There is an obstacle between the

Remove the obstacle.

remote control and the projector.

 

 

 

You are too far away from the

Stand within 6 meters (19.5 feet) of the

projector.

projector.

 

 

44 Troubleshooting

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Welcome Copyright DisclaimerTable of contents Iv Table of contents Supported timing for Component-YPbPr inputTable of contents Memo Vi Table of contents But could fail if power cuts or surges Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Rear side Projector exterior viewFront / upper side Lower sideMation Controls and functionsExternal control panel Turns the projector on or offII/ Freeze Remote controlExit 5Up, 6 Down 3Left, Right4Pull out the battery holder Remote control effective rangeReplacing the remote control battery Push the holder into the remote controlPositioning your projector Choosing a locationObtaining a preferred projected image size Positioning your projector 1219 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1500Connection Connecting a computer or monitorConnecting a computer Connecting a monitor Connecting Video source devices Best video qualityConnecting a Component Video source device 1080i 50/ 60 HzConnecting an S-Video source device Device Video cable Audio cablesConnecting a composite Video source device Operation Utilizing the password functionTo set a password Start upTo change the password If you forget the passwordTo enter the password recall procedure Password set-up and return to the on-screen menuFine-tuning the image size and clarity Adjusting the heightAuto-adjusting the image Correcting keystone For exampleHiding the image Selecting an application modeSwitching input signal Freezing the image Disconnect the power cord from the wall socketRemote paging operations ShutdownMenu operation Menu systemKeystone Using the menusPicture menu Picture menu Selected Color TempDepends on BrightnessPro-Picture menu Setting menu Advance menu Auto Off off Mode offHigh Altitude EconomicInformation menu ResolutionMode Equivalent Lamp Hour SystemMaintenance Care of the projectorMessage Status Lamp informationCalculation of lamp hour Disconnect the lamp connector from the projector Maintenance Replacing the lampMaintenance Restart the projector Temperature informationResetting the lamp counter Iii. Wait about 5 seconds to let the OSD disappearLight Status & Description Power Temp Lamp Lamp events IndicatorsLight Status & Description Power Temp Lamp Power events Projector is under normal operationThermal events For assistanceMaintenance Make sure that it is switched on TroubleshootingPlug the power cord into the AC inlet on Cause RemedySpecifications Projector specificationsSupported timing for Component-YPbPrinput Timing chartSupported timing for PC input Supported timing for Video and S-Video inputsDimensions Unit mm SpecificationsWarranty WarrantyLimited Warranty EEC statement Regulation StatementsFCC statement MIC statement

MP610 specifications

The BenQ MP610 is a versatile, portable projector designed to deliver high-quality visuals for both home entertainment and professional presentations. Compact and lightweight, this projector offers remarkable convenience, making it easy to transport for on-the-go use. With its sleek design, the MP610 fits seamlessly into any environment, whether it’s a small meeting room or a cozy home theater.

One of the standout features of the BenQ MP610 is its DLP (Digital Light Processing) technology, which ensures brilliant color reproduction and sharp image quality. The projector boasts a resolution of 800 x 600 pixels, providing clear and vibrant visuals that engage the audience, whether for business slideshows or movies. The 2000 ANSI lumens brightness effectively illuminates images, making it suitable for use in various lighting conditions.

The MP610 supports a variety of input options, including HDMI, VGA, and USB, allowing users to connect multiple devices such as laptops, smartphones, and tablets. This flexibility enhances its functionality, making it a perfect choice for classroom settings, corporate environments, or personal entertainment systems.

In terms of audio, the projector is equipped with built-in speakers, offering satisfactory sound for small gatherings. For larger audiences, users can easily connect external audio devices to enhance the sound experience. The MP610 also features a 2000:1 contrast ratio, ensuring deeper blacks and brighter whites, which enhances the overall viewing experience.

The lamp life of the BenQ MP610 is another impressive characteristic, offering up to 4000 hours in standard mode and even longer in economic mode. This longevity reduces the need for frequent lamp replacements, ultimately lowering operating costs and improving user convenience.

For those who need to set up quickly and efficiently, the projector includes automatic keystone correction, which adjusts the image to ensure that it maintains its optimal rectangular shape, even when positioned at an angle. This feature saves time during setup and guarantees a professional presentation every time.

Overall, the BenQ MP610 stands out as a reliable projector that combines portability, versatile connectivity, and quality performance, making it an ideal choice for anyone looking to enhance their viewing experience, whether for work or leisure. Its blend of advanced technologies and user-friendly features makes it a valuable tool for any presenter or home theater enthusiast.
Top Page Image Contents