BenQ MP610 user manual Operation, Start up, Utilizing the password function, To set a password

Page 27

Operation

Start up

1.Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted).

Check that the Power indicator on the projector lights orange after power has been applied.

2.Remove the lens cap. If it is left on, it could become deformed due to heat.

3.Press and hold (for 2 seconds) the Power button on the remote control or projector to start the unit. The

Power indicator light flashes green and stays green when the unit is on.

The start up procedure takes about 30 seconds after pressing Power. In the later stage of start up, a default BenQ logo is projected.

4. If you are prompted for a password, press the arrow buttons to select the four password digits, then press Auto. For information about the password function, refer to "Utilizing the password function" on page 21.

5.Switch all of the connected equipment on.

6.The projector will start to search for input signals. The current input source being scanned displays at the center of the screen. The search will continue until an input source signal is detected.

You can also press Source on the projector or remote control to select your desired input signal. For more information, please refer to "Switching input signal" on page 25.

If the frequency/ resolution of the input signal exceeds the projector’s operating range, you will see the message “Out of Range” displayed on a blank screen.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the on-screen menu. For details of the on-screen menu operation, please refer to "Using the menus" on page 28 for information.

WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

To set a password:

CAUTION: Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Open the on-screen menu and go to Setting > Password. Select On by pressing Left 3or Right4.

Operation 21

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsTable of contents Memo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Projector features IntroductionIntroduction Shipping contents Lower side Projector exterior viewFront / upper side Rear sideTurns the projector on or off Controls and functionsExternal control panel Mation5Up, 6 Down 3Left, Right4 Remote controlExit II/ FreezePush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connecting a computer or monitor Connecting a computerConnection Connecting a monitor Best video quality Connecting Video source devices1080i 50/ 60 Hz Connecting a Component Video source deviceDevice Video cable Audio cables Connecting an S-Video source deviceConnecting a composite Video source device Start up Utilizing the password functionTo set a password OperationPassword set-up and return to the on-screen menu If you forget the passwordTo enter the password recall procedure To change the passwordAdjusting the height Auto-adjusting the imageFine-tuning the image size and clarity For example Correcting keystoneSelecting an application mode Switching input signalHiding the image Shutdown Disconnect the power cord from the wall socketRemote paging operations Freezing the imageMenu system Menu operationUsing the menus Picture menuKeystone Picture menu Brightness Color TempDepends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offLamp Hour System ResolutionMode Equivalent Information menuCare of the projector MaintenanceLamp information Calculation of lamp hourMessage Status Replacing the lamp Disconnect the lamp connector from the projector MaintenanceMaintenance Iii. Wait about 5 seconds to let the OSD disappear Temperature informationResetting the lamp counter Restart the projectorProjector is under normal operation IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsWarranty Limited WarrantyWarranty MIC statement Regulation StatementsFCC statement EEC statement

MP610 specifications

The BenQ MP610 is a versatile, portable projector designed to deliver high-quality visuals for both home entertainment and professional presentations. Compact and lightweight, this projector offers remarkable convenience, making it easy to transport for on-the-go use. With its sleek design, the MP610 fits seamlessly into any environment, whether it’s a small meeting room or a cozy home theater.

One of the standout features of the BenQ MP610 is its DLP (Digital Light Processing) technology, which ensures brilliant color reproduction and sharp image quality. The projector boasts a resolution of 800 x 600 pixels, providing clear and vibrant visuals that engage the audience, whether for business slideshows or movies. The 2000 ANSI lumens brightness effectively illuminates images, making it suitable for use in various lighting conditions.

The MP610 supports a variety of input options, including HDMI, VGA, and USB, allowing users to connect multiple devices such as laptops, smartphones, and tablets. This flexibility enhances its functionality, making it a perfect choice for classroom settings, corporate environments, or personal entertainment systems.

In terms of audio, the projector is equipped with built-in speakers, offering satisfactory sound for small gatherings. For larger audiences, users can easily connect external audio devices to enhance the sound experience. The MP610 also features a 2000:1 contrast ratio, ensuring deeper blacks and brighter whites, which enhances the overall viewing experience.

The lamp life of the BenQ MP610 is another impressive characteristic, offering up to 4000 hours in standard mode and even longer in economic mode. This longevity reduces the need for frequent lamp replacements, ultimately lowering operating costs and improving user convenience.

For those who need to set up quickly and efficiently, the projector includes automatic keystone correction, which adjusts the image to ensure that it maintains its optimal rectangular shape, even when positioned at an angle. This feature saves time during setup and guarantees a professional presentation every time.

Overall, the BenQ MP610 stands out as a reliable projector that combines portability, versatile connectivity, and quality performance, making it an ideal choice for anyone looking to enhance their viewing experience, whether for work or leisure. Its blend of advanced technologies and user-friendly features makes it a valuable tool for any presenter or home theater enthusiast.
Top Page Image Contents