BenQ MX662 user manual MW663

Page 15

The screen aspect ratio is 16:10 and the projected picture is 16:10

MW663

Maximum zoom

Minimum zoom

Vertical offset

Screen

Center of lens

Projection distance

	Screen size			Distance from screen (mm)			Vertical
Diagonal		W	H	Min length	Average	Max length	offset
Inch	mm	(mm)	(mm)	(max. zoom)	Average	(min. zoom)	(mm)
40	1016	862	538	1046	1203	1359	54

50	1270	1077	673	1307	1503	1699	67

60	1524	1292	808	1569	1804	2039	81

80	2032	1723	1077	2092	2405	2719	108

100	2540	2154	1346	2614	3007	3399	135

120	3048	2585	1615	3137	3608	4078	162

150	3810	3231	2019	3922	4510	5098	202

200	5080	4308	2692	5229	6013	6797	269

220	5588	4739	2962	5752	6614	7477	296

250	6350	5385	3365	6536	7516	8497	337

300	7620	6462	4039	7843	9020	10196	404

For example, if you are using an 120-inch screen, the recommended projection distance is 3608 mm and the vertical offset is 162 mm.

If your measured projection distance is 6.0 m (6000 mm), the closest match in the "Distance from screen (mm)" column is 6013 mm. Looking across this row shows that a 200'' (about 5.1 m) screen is required.

All measurements are approximate and may vary from the actual sizes.

BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

Positioning your projector

15

Image 15

Contents MX662/MW663 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableMax length Offset Inch Projection dimensionsObtaining a preferred projected image size MX662MW663 Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX662 MW663 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Fine Tuning 3D Color Picture ModeTemperature Color TemperatureSearch TimerInstallation SettingsReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timerMaintenance Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs PixelDisclaimer Warranty and Copyright informationLimited warranty Copyright