BenQ MX662 user manual Advanced

Page 39

	Main menu	Sub-menu		Options

		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
			Lamp Mode	Normal/Economic/SmartEco
		Lamp Settings	Reset Lamp Timer
			Equivalent Lamp
		Security	Change Password
		Security	Change Security	Power On Lock
		Settings	Change Security	Power On Lock
		Settings	Settings	Web Control Lock
			Settings	Web Control Lock
		Baud Rate		2400/4800/9600/14400/19200/
		Baud Rate		38400/57600/115200
	5.			38400/57600/115200
	5.	Test Pattern		On/Off
	SYSTEM
	SYSTEM		Closed Caption	On/Off
	SETUP:	Closed Caption	Enable	On/Off
	SETUP:	Closed Caption	Enable
	Advanced		Caption Version	CC1/CC2/CC3/CC4
			Network	On/Off
		Standby	Monitor Out	On/Off
		Settings	Audio Pass	Off/Computer 1/Computer 2/
			Through	Video,S-Video/HDMI
				Status
				SSID
			Wireless LAN	SSID Display
		Network	Wireless LAN	IP Address
		Network		IP Address
		Settings		Connection Mode
				Apply
			Projection Log In	On/Off
			Code
		Reset All Settings
				•	Source
				•	Picture Mode
	6.			•	Resolution
	INFORMA	Current System Status		•	Lamp Mode
	INFORMA	Current System Status		•	3D Format
	TION			•	3D Format
	TION			•	Color System
				•	Equivalent Lamp
				•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 39

Image 39

Contents MX662/MW663 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableMax length Offset Inch Projection dimensionsObtaining a preferred projected image size MX662MW663 Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX662 MW663 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Fine Tuning 3D Color Picture ModeTemperature Color TemperatureSearch TimerInstallation SettingsReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timerMaintenance Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs PixelDisclaimer Warranty and Copyright informationLimited warranty Copyright