BenQ MX662 Indicators, Light Status & Description Power events, Lamp events, Thermal events

Page 53

Indicators

Light

Status & Description

Power events

	Orange	Off	Off	Stand-by mode.
	Green	Off	Off	Powering up.
	Flashing	Off	Off	Powering up.
	Flashing
	Green	Off	Off	Normal operation.
	Orange	Off	Off	Normal power-down cooling
	Flashing	Off	Off	Normal power-down cooling
	Flashing
	Red	Off	Off	Download
	Green	Off	Red	CW start fail
	Red Flashing	Off	Off	Scaler shutdown fail (data abort)
			Lamp events

	Off	Off	Red	Lamp1 error in normal operation
	Off	Off	Red	Lamp is not lit up
	Off	Off	Flashing	Lamp is not lit up
			Flashing
			Thermal events

	Red	Red	Off	Fan 1 error (the actual fan speed is +25% outside
	Red	Red	Off	the desired speed)
				the desired speed)
	Red	Red	Off	Fan 2 error (the actual fan speed is +25% outside
	Red	Flashing	Off	the desired speed)
		Flashing		the desired speed)
	Red	Green	Off	Fan 3 error (the actual fan speed is +25% outside
	Red	Green	Off	the desired speed)
				the desired speed)
	Red	Green	Off	Fan 4 error (the actual fan speed is +25% outside
	Red	Flashing	Off	the desired speed)
		Flashing		the desired speed)
	Green	Red	Off	Temperature 1 error (over limited temperature)
	Green	Red	Off	Thermal Sensor 1 open error
	Green	Flashing	Off	Thermal Sensor 1 open error
		Flashing
	Green	Green	Off	Thermal Sensor 1 short error
	Green	Green	Off	Thermal IC #1 I2C Connection error
	Green	Flashing	Off	Thermal IC #1 I2C Connection error
		Flashing
	Green	Red	Off	Temperature 2 error (over limited temperature)
	Flashing	Red	Off	Temperature 2 error (over limited temperature)
	Flashing
	Green	Red	Off	Thermal Sensor 2 open error
	Flashing	Flashing	Off	Thermal Sensor 2 open error
	Flashing	Flashing
	Green	Green	Off	Thermal Sensor 2 short error
	Flashing	Green	Off	Thermal Sensor 2 short error
	Flashing
	Green	Green	Off	Thermal IC #2 I2C Connection error
	Flashing	Flashing	Off	Thermal IC #2 I2C Connection error
	Flashing	Flashing

Maintenance 53

Image 53

Contents MX662/MW663 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsMX662 Max length Offset InchMW663 Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX662 MW663 About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSettings SearchOperation System Setup Basic menu Function DescriptionRemote ReceiverAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timerMaintenance Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputPixel TimingLimited warranty Warranty and Copyright informationCopyright Disclaimer