BenQ MX662 Hiding the image, Locking control keys, Operating in a high altitude environment

Page 32

Hiding the image

In order to draw the audience's full attention to the presenter, you can use ECO BLANK on the projector or remote control to hide the screen image. When this function is activated with an audio input connected, the audio can still be heard.

You can set the blank time in the SYSTEM SETUP: Basic > Operation Settings > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen. The length of time can be set from 5 to 30 minutes in 5-minute increments.

If the preset time spans are not suitable for your presentation, select Disable.

No matter Blank Timer is activated or not, you can press most of the keys on the projector or remote control to restore the picture.

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is

on, no control keys on the projector will operate except POWER.

1.Go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select On by

pressing / on the projector or remote control. A confirmation message appears.

2.Highlight Yes and press MODE/ENTER to confirm.

To release panel key lock, use the remote control to enter the SYSTEM SETUP: Basic > Panel Key Lock menu and press / to select Off.

• Keys on the remote control are still active when panel key lock is enabled.

•If you press POWER to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on.

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea level, and ambient temperature is between 0°C–35°C.

Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.

To activate the High Altitude Mode:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight High Altitude Mode and press / select On. A confirmation message appears.

3.Highlight Yes and press MODE/ENTER.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-

32 Operation

Page 31 Page 33
Image 32
Page 31 Page 33
Contents MX662/MW663 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeMX662 Max length Offset InchMW663 Connection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio MX662 MW663Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardPresenting from a USB Reader Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorTimer InstallationSettings SearchSystem Setup Basic menu Function Description OperationRemote ReceiverSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkStatus CurrentSystem Maintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageReplacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out of the projectorMaintenance Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YP bP r input Supported timing for Video and S-Video inputsPixel TimingWarranty and Copyright information Limited warrantyCopyright Disclaimer
Top Page Image Contents