BenQ MX662 System Setup Advanced menu Function Description, Standby, Network, Reset All

Page 45

5. SYSTEM SETUP: Advanced menu

	Function	Description
		Network
		Selecting On enables the function. The projector is able to provide the
		network function when it is in standby mode.
		Monitor Out
		Selecting On enables the function. The projector can output a VGA
		signal when it is in standby mode and the COMPUTER 1 jack is
	Standby	correctly connected to devices. See "Connection" on page 16 for how
	Settings	to make the connection.
	Settings	Audio Pass Through
		Audio Pass Through
		The projector can play sound when it is in standby mode and the
		corresponding jacks are correctly connected to devices. Press / to
		choose the source that you wish to use. See "Connection" on page 16
		for how to make the connection.
		Enabling this function slightly increases the standby power consumption.

	Network	Wireless LAN
	Network	Projection Log In Code
	Settings	Projection Log In Code
	Settings	See BenQ Network Projector Operation Guide for details.
		See BenQ Network Projector Operation Guide for details.

	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Phase, H. Size, Projector
	Settings
	Settings	Installation, Color Space Conversion, High Altitude Mode, Security
		Settings and Baud Rate.

Operation 45

Image 45

Contents MX662/MW663 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsMX662 Max length Offset InchMW663 Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX662 MW663 About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSettings SearchOperation System Setup Basic menu Function DescriptionRemote ReceiverAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timerMaintenance Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputPixel TimingLimited warranty Warranty and Copyright informationCopyright Disclaimer