BenQ MX662 user manual Maintenance, Care of the projector

Page 47

Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens and case clean.

Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off the projector and let it cool down completely before cleaning the lens.

Use a canister of compressed air to remove dust.

If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in "Shutting down the projector" on page 36 and unplug the power cord.

To remove dirt or dust, wipe the case with a soft, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 55 or consult your dealer about the range.

Retract the adjuster feet.

Remove the battery from the remote control.

Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

Maintenance 47

Image 47
Contents MX662/MW663 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableMax length Offset Inch Projection dimensionsObtaining a preferred projected image size MX662MW663 Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX662 MW663 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Fine Tuning 3D Color Picture ModeTemperature Color TemperatureSearch TimerInstallation SettingsReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timerMaintenance Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs PixelDisclaimer Warranty and Copyright informationLimited warranty Copyright