BenQ MX620ST Connecting video source devices, Connecting audio, Terminal name Terminal appearance

Page 17

•If you wish to use this connection method when the projector is in standby mode, make sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings" on page 47 for details.

Connecting video source devices

You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Terminal name	Terminal appearance	Picture quality
HDMI		Best
Component Video		Better
S-Video		Good
Video		Normal

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 17 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 17

Image 17

Contents MS619ST/MX620ST/MW621ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal LengthMW621ST Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signalChanging Color Space Magnifying and searching for detailsSelecting the aspect ratio MS619ST/ MW621ST About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu 3D Sync Invert Apply 3D SettingsTeaching Template Description Temperature Picture menu Function Description Picture ModeReference ModeReset Picture Fine Tuning 3D ColorSettings Quick Auto TimerOperation System Setup Basic menu Function DescriptionRemote ReceiverAltitude System Setup Advanced menu Function Description HighAudio LampStandby Reset AllNetwork CurrentCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Maintenance Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer