BenQ MX620ST user manual Standby, Network, Reset All, Current, System, Status

Page 47

		Function
	5. SYSTEM	Standby
	SETUP: Advanced	Settings
	SETUP: Advanced	Network
	menu	Network
		Settings
		Reset All
		Reset All
		Settings

6.
INFORMATIONmenu	Current
	Current
	System
	Status

Description

Network

Selecting On enables the function. The projector is able to provide the network function when it is in standby mode.

Monitor Out

Selecting On enables the function. The projector can output a VGA signal when it is in standby mode and the COMPUTER jack is correctly connected to devices. See "Connection" on page 16 for how to make the connection.

Audio Pass Through

The projector can play sound when it is in standby mode and the corresponding jacks are correctly connected to devices. Press / to choose the source that you wish to use. See "Connection" on page 16 for how to make the connection.

Enabling this function slightly increases the standby power consumption.

See BenQ Network Projector Operation Guide for details.

Returns all settings to the factory preset values.

The following settings will still remain: Keystone, User 1, User 2, Color Space Conversion, Language, Projector Installation, High Altitude Mode, Security Settings, Baud Rate and Network Settings.

Source

Shows the current signal source.

Picture Mode

Shows the selected mode in the PICTURE menu.

Lamp Mode

Shows the current lamp mode.

Resolution

Shows the native resolution of the input signal.

3D Format

Shows the current 3D mode.

Color System

Shows the input system format.

Equivalent Lamp Hour

Displays the number of hours the lamp has been used.

Firmware Version

Shows the firmware version of your projector.

Operation 47

Image 47

Contents MS619ST/MX620ST/MW621ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableLength Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalMW621ST Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signalChanging Color Space Magnifying and searching for detailsSelecting the aspect ratio MS619ST/ MW621ST About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu 3D Sync Invert Apply 3D SettingsTeaching Template Description Mode Picture menu Function Description Picture ModeTemperature ReferenceTimer Fine Tuning 3D ColorReset Picture Settings Quick AutoReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioCurrent Reset AllStandby NetworkCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright