BenQ MX620ST user manual If you forget the password, Entering the password recall procedure

Page 23
Password Error
Please try again.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for 3 seconds, and the INPUT PASSWORD message follows. You can retry by entering another six-digit password, or if you did not

record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 23 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1.Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact BenQ

Customer Center.

Recall Code:

255 255 255 255

MENU Exit

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.

2.Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.

3.Enter the old password.

i.If the password is correct, another message “INPUT NEW PASSWORD” appears.

ii.If the password is incorrect, the password error message appears lasting for three seconds, and the message “INPUT CURRENT PASSWORD” appears for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press MENU/EXIT.

Operation 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MS619ST/MX620ST/MW621ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableLength Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalMW621ST Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signalChanging Color Space Magnifying and searching for detailsSelecting the aspect ratio MS619ST/ MW621ST About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu 3D Sync Invert Apply 3D SettingsTeaching Template Description Mode Picture menu Function Description Picture ModeTemperature ReferenceTimer Fine Tuning 3D ColorReset Picture Settings Quick AutoReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioCurrent Reset AllStandby NetworkCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents