BenQ MX620ST user manual Operation, Starting up the projector

Page 18

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire.

2.Press POWER to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 34 for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

3.If the projector is activated for the first time, select your OSD language following the on-screen instructions.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 22 for details.

5.Switch all of the connected equipment on.

6.The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message “No Signal” will continue displaying until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 24 for details.

•If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message “Out of Range” displayed on the background screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 58 for details.

•If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode.

18 Operation

Image 18

Contents MS619ST/MX620ST/MW621ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size LengthMW621ST Connection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Switching input signal Disabling the password functionMagnifying and searching for details Changing Color SpaceSelecting the aspect ratio About the aspect ratio MS619ST/ MW621STSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementSetting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardPresenting from a USB Reader Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Apply 3D Settings Teaching Template Description3D Sync Invert Reference Picture menu Function Description Picture ModeTemperature ModeSettings Quick Auto Fine Tuning 3D ColorReset Picture TimerRemote System Setup Basic menu Function DescriptionOperation ReceiverAudio System Setup Advanced menu Function Description HighAltitude LampNetwork Reset AllStandby CurrentMaintenance Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Maintenance Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YPbPrinput TimingSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer