BenQ MX620ST user manual Switching input signal, Disabling the password function

Page 24

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. Press MODE/ENTER. The message “INPUT PASSWORD” appears. Enter the current password.

i.If the password is correct, the OSD menu returns to the Security Settings page.

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

Press to highlight Web Control Lock and press / to select Off. Now the Web Control Lock is released and projector settings can be changed via the Projector Network Display System.

ii.If the password is incorrect, the password error message appears lasting for three seconds, and the message “INPUT PASSWORD” appears for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

1.Press SOURCE on the projector or remote control. A source selection bar appears.

2.Press / until your desired signal is selected and press MODE/ENTER.

Once detected, the selected source information will display at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another signal.

•The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

•The native display resolution of this projector is in a 4:3 (MS619ST/MX620ST)/16:10 (MW621ST) aspect ratio. For

best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 26 for details.

•Firewall in the PC must be switched off to allow USB Display to work.

24 Operation

Page 23 Page 25
Image 24
Page 23 Page 25
Contents MS619ST/MX620ST/MW621ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal LengthMW621ST Connection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Switching input signal Disabling the password functionMagnifying and searching for details Changing Color SpaceSelecting the aspect ratio About the aspect ratio MS619ST/ MW621STUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementSetting the presentation timer Resetting current or all picture modesSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardPresenting from a USB Reader Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Apply 3D Settings Teaching Template Description3D Sync Invert Picture menu Function Description Picture Mode TemperatureReference ModeFine Tuning 3D Color Reset PictureSettings Quick Auto TimerSystem Setup Basic menu Function Description OperationRemote ReceiverSystem Setup Advanced menu Function Description High AltitudeAudio LampReset All StandbyNetwork CurrentMaintenance Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Maintenance Resetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YPbPrinput TimingSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer
Top Page Image Contents