BenQ MX620ST user manual Advanced

Page 40

	Main menu	Sub-menu		Options

		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
			Lamp Mode	Normal/Economic/SmartEco/
			Lamp Mode	LampSave
		Lamp Settings		LampSave
		Lamp Settings	Reset Lamp Timer
			Reset Lamp Timer
			Equivalent Lamp Hour
		Security	Change Password
		Security	Change Security	Power On Lock
		Settings	Change Security	Power On Lock
		Settings	Settings	Web Control Lock
			Settings	Web Control Lock
	5.	Baud Rate		2400/4800/9600/14400/19200/
	5.	Baud Rate		38400/57600/115200
	SYSTEM
	SYSTEM	Test Pattern		On/Off
	SETUP:		Closed Caption	On/Off
	Advanced	Closed Caption	Enable	On/Off
	Advanced	Closed Caption	Enable
			Caption Version	CC1/CC2/CC3/CC4
			Network	On/Off
		Standby	Monitor Out	On/Off
		Settings	Audio Pass	Off/Audio in/Audio L/R/HDMI
			Through	Off/Audio in/Audio L/R/HDMI
			Through
				Status
				SSID
		Network	Wireless LAN	IP Address
		Network		Connection Mode
		Settings		Connection Mode
		Settings		Apply
				Apply
			Projection Log In	On/Off
			Code
		Reset All Settings
				•	Source
				•	Picture Mode
	6.			•	Lamp Mode
	INFORMA	Current System Status		•	Resolution
	INFORMA	Current System Status		•	3D Format
	TION			•	3D Format
	TION			•	Color System
				•	Equivalent Lamp Hour
				•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

40 Operation

Image 40

Contents MS619ST/MX620ST/MW621ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal LengthMW621ST Connection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Switching input signal Disabling the password functionMagnifying and searching for details Changing Color SpaceSelecting the aspect ratio About the aspect ratio MS619ST/ MW621STUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardPresenting from a USB Reader Direct power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Teaching Template Description Apply 3D Settings3D Sync Invert Picture menu Function Description Picture Mode TemperatureReference ModeFine Tuning 3D Color Reset PictureSettings Quick Auto TimerSystem Setup Basic menu Function Description OperationRemote ReceiverSystem Setup Advanced menu Function Description High AltitudeAudio LampReset All StandbyNetwork CurrentMaintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Maintenance Resetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YPbPrinput TimingSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer