Onkyo TXSR307 instruction manual First Time Setup, Using Audyssey 2EQ

Page 34

First Time Setup—Continued

Using Audyssey 2EQ™

Notes:

If the AV receiver is muted, it will be unmuted automatically when the Audyssey 2EQ Room Correction and Speaker Setup starts.

Room correction and speaker setup cannot be performed while a pair of headphones is connected.

It takes about 10 minutes to complete the room correction and speaker setup for three positions. Total measurement time varies depending on the number of speakers.

Do not connect or disconnect any speakers during room correction and speaker setup.

ON/STANDBY

Speaker setup microphone

SETUP MIC

ENTER

1

Turn on the AV receiver.

 

2

Set the speaker setup

 

 

microphone at the Main

 

Listening Position a (page 33),

 

and connect it to the SETUP MIC

 

jack.

 

Audyssey indicator

Notes:

Before starting Audyssey 2EQ Room Correction and Speaker Setup, arrange the room and connect the speakers as you would for enjoying movies. Changes to the room after auto setup requires you run the auto setup again, as room EQ characteristics may have changed.

When starting the room correction and speaker setup, do not stand between the speakers and microphone, and avoid obstacles blocking the path between speakers and microphone. This will produce inaccurate results.

Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce innacurate results.

Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices.

Cell phones should be turned off or placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

3

Press [ENTER].

 

 

The room calibration and speaker setup starts.

Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measure- ments and do not stand between speakers and the microphone.

Note:

You can cancel the Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

4

When the following display appears,

 

 

move the speaker setup microphone to

 

measurement point b (page 33), and

 

then press [ENTER].

 

 

 

 

 

 

Audyssey 2EQ performs more measurements. This takes a few minutes.

34

Image 34
Contents Connection Basic Operations Using the Listening ModesIntroduction OthersImportant Safety Instructions AvisPreventing Hearing Loss Caution PrecautionsPower Batteries and Heat Exposure WarningPrecautions Supplied AccessoriesHow to mount the AC plug Contents Processing FeaturesAmplifier ConnectionsFront & Rear Panels Front PanelFront & Rear Panels DisplayRear Panel DVD/BD VCR/DVR IN/OUTSubwoofer PRE OUT Remote Controller Controlling the AV receiverInstalling the Batteries Remote ControllerAiming the Remote Controller Speaker Set a Main Room Enjoying Home TheaterSpeaker Sets a and B Speaker Set B Sub RoomConnecting the AV Receiver Connecting Your SpeakersStrip about 5/8 Connecting the AV ReceiverConnecting the Speaker Cables Strip 3/8 10 mmConnecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown North American ModelConnecting an Outdoor AM Antenna Connecting an Outdoor FM AntennaUsing a TV/FM Antenna Splitter Optical Digital Jacks AV Connection Color Coding About AV ConnectionsAV Cables and Jacks Video Connection Formats Connecting Audio and Video Signals to the AV receiverWhich Connections Should I Use? Audio Connection FormatsAbout Copyright Protection Connecting Components with HdmiAbout Hdmi Pass-ThruMaking Hdmi Connections TipAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD/BD player Connecting a VCR or DVR for Playback Connecting a VCR or DVR for Recording Make the audio connection aSatellite, cable, set-top box, etc Connecting a Portable Audio player Connecting a Camcorder, Game Console, or Other DeviceMake the video connection a Make the audio connection a Connecting a CD Player or Turntable CD Player or Turntable MM with Built-in Phono Preamp StepConnecting a Cassette, CDR, MiniDisc, or DAT Recorder If Your iPod Supports Video Connecting an RI DockIf Your iPod Doesn’t Support Video Auto Power On/Standby Connecting Onkyo u ComponentsConnecting the Power Cord Direct ChangeTurning On and Standby Turning On the AV receiverUp and Running in a Few Easy Steps Audyssey 2EQ Room Correction and Speaker Setup First Time SetupMeasurement Positions First Time Setup Using Audyssey 2EQChanging the Speaker Settings Manually Error MessagesTo Retry the Room Correction and Speaker Setup Using a Powered SubwooferComponent Video Input Setup Digital Input SetupChanging the Input Display Basic AV receiver Operation Select a listening mode and enjoyBasic Operations Start playback on the source componentBasic Operations Setting the Display BrightnessUsing the Sleep Timer Muting the AV receiverDisplaying Source Information 7Using HeadphonesAdjusting the Bass & Treble BassSpecifying the Digital Signal Format Using the Music OptimizerAuto default Use the Left and Right e/r AM/FM Frequency Step Setup not European modelsListening to the Radio Buttons to selectListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Use the AM or FM input selector button to select AM or FMDisplaying AM/FM Radio Information Deleting Presets Presetting AM/FM StationsSelecting Presets Using RDS European models only RDS Program Types PTYFinding Stations by Type PTY Displaying Radio Text RTListening to Traffic News TP Recording from Different AV Sources RecordingRecording the Input Source MOVIE/TV button Game button Using the Listening ModesSelecting the Listening Modes Stereo buttonListening Modes Available for Each Source Format Using the Listening ModesMono/Multiplex Sources Stereo Source Multichannel Sources DTSAbout the Listening Modes Onkyo Original DSP ModesCommon Procedures in Setup Menu Advanced SetupSpeaker Settings Advanced Setup Sp Distance Speaker DistanceLevel Cal Speaker Levels Calibration Equalizer Equalizer SettingsLeft and Right e/ r buttons to adjust the level at that Use the Down w button to select Ch, and then use the LeftAudio Adjust Multiplex/Mono Settings Audio Adjust SettingsPLII/Neo6 Settings Theater-Dimensional Setting Audyssey SettingsDyn Vol Dynamic Volume Dynamic EQ Off Audyssey Dynamic EQ offWhile holding down the Receiver button, press and hold down Hardware SetupHardware Remote ID Use the number buttons to enter ID 1, 2, orUsing the Audio Settings Speaker Levels Audyssey Dynamic VolumeMusic Optimizer SyncEntering Remote Control Codes Preprogrammed Remote Control CodesControlling Other Components Resetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Onkyo Components Connected via u Controlling Other ComponentsControlling a DVD Player Cancels functions and clears entered numbers Controlling a CD Player, CD Recorder, or MD PlayerControlling an RI Dock Used with the shuffle function Troubleshooting Troubleshooting Can’t record Sound changes when I connect my headphonesCan’t control other components How do I change the language of a multiplex sourceVideo Section SpecificationsAmplifier Section Tuner Section3 4 4 9 2 1 a