3M S10 manual Option Menu, Volume, Screen Type, Lamp Time

Page 31

Multifunctional Settings (continued)

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

MENU

MAIN

VOLUME

16

PICTURE-1

SCREEN TYPE

4:3

PICTURE-2

LAMP TIME

1234h

INPUT

FILTER TIME

21h

AUTO

RESET

 

SCREEN

 

 

OPTION

 

 

: SELECT

Item

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

VOLUME

Adjust Volume: High

⇔

 

Low

 

 

 

 

 

 

 

 

 

 

Select the Screen Type:

 

 

 

 

 

 

4:3

⇔

16:9

 

⇔

16:9

⇔

16-9

SCREEN TYPE

• Please select the screen type used and the picture position in case of 16:9.

 

This selection is used as basic information for a suitable display. This function

 

should be performed before other picture adjustment.

 

 

 

 

 

 

To begin the operation of this item, please press the

button of the

 

projector or the RESET button of the remote control for 3 seconds.

 

Reset the Lamp Timer:

 

 

 

 

 

 

Selecting the RESET performs this function.

 

 

 

RESET

⇒

CANCEL

 

 

 

 

 

•The numerical value of four digits shown on this menu is the projector use time since the last RESET operation of this item. The value is reset to 0 at the

LAMP TIME

same time the RESET is selected.

•The value of this function is used to display the message of “CHANGE THE LAMP”. So this function must be performed only immediately after replacing the lamp.

Do not perform this function unless you have replaced the lamp. Perform this function every time the lamp is replaced. Incorrect performing of this function causes incorrect operation of the message function.

•Please see to the section “Lamp” about replacing the lamp.

To begin the operation of this item, please press the button of the projector or the RESET button of the remote control for 3 seconds.

Reset the Filter Timer:

Selecting the RESET performs this function.

RESET

⇒ CANCEL

•The numerical value of four digits shown on this menu is the projector use time since the last RESET operation of this item. The value is reset to 0 at the same time the RESET is selected.

FILTER TIME • The value of this function is used to display the message of “CLEAN THE AIR FILTER”. So this function must be performed only immediately after cleaning or replacing the air filter.

Do not perform this function unless you have cleaned or replaced the air filter. Perform this function every time the air filter is cleaned or replaced. Incorrect performing of this function causes incorrect operation of the message function.

•Please see to the section “Air Filter” about cleaning and replacing the air filter.

 

Reset the OPTION Menu Items:

 

Selecting the EXECUTE performs this function.

RESET

EXECUTE

⇒ CANCEL

 

• The SCREEN TYPE item is returned to the initial setting. Note that the items

 

VOLUME, LAMP TIME and FILTER TIME are not reset.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents S10 Multimedia Projector Contents Preparation Projector FeaturesSlowly turn the projector so that the top is facing up Part NamesProjector Attaching The BaseProjector To adjust the keystoneRemote Control Arrangement Setting UpTwisting the elevator feet by hand Adjusting The Projectors ElevatorAdjust the height of the projector by As necessary, you can also finelyConnecting Your Devices AUDIO-L AUDIO-R G B R Connecting to a computerConnecting Power Supply Putting Batteries Remote ControlRemove Battery cover Close Battery coverOperating The Remote Control Remote control Power ON/OFFTurning On The Power Make sure that the power cord isUse the focus ring to focus the picture Selecting An Input SignalSelecting a RGB signal Use the zoom ring to adjust the screen SizeSwitch the power switch to O OFF Turning Off The PowerOperating Adjusting The VolumeTemporarily Muting The Sound Use Buttons to adjust Position Adjusting The PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeaturePress the Magnify on button Using The Magnify FeatureUse Buttons to adjust the zoom Level Freezing The ScreenSelecting The Aspect Ratio Signal SearchingTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu LOAD4 Load/Save a SettingReset the PICTURE-1 Menu Items Picture 1 MenuSize PhasePicture 2 Menu PositionFrame Lock Input MenuColor Space VideoS2-ASPECT Input MenuVideo NR InformationAuto Menu AdjustSearch Start UP Screen MenuMessage Lamp Time VolumeOption Menu Screen TypeLamp Replacing The Lamp Air Filter Reset the filter timerCaring For The Air Filter Filter cover Replacing The Air FilterHold the release buttons of the air Filter, while pulling down itCaring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRelated Messages Power Lamp Temp Description Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Video Input Ports SpecificationsSpecification RGB Input Ports Audio PortsNot Included with Basic Packet ………………………………… Part Number AccessoriesAccessories ……………………………………………………… Part Number How to OrderDN00571 S10OGENG

S10 specifications

The 3M S10 is a state-of-the-art personal safety device designed to enhance worker safety across various industrial settings. This innovative product seamlessly combines advanced technology with ergonomic design to provide users with reliable protection and comfort during their daily tasks.

One of the standout features of the 3M S10 is its advanced respiratory protection capabilities. It employs a powerful filtration system that effectively captures airborne particles, gases, and vapors, ensuring that workers are shielded from harmful contaminants. The S10 is equipped with a P100 filter that offers a high level of filtration efficiency, capturing at least 99.97% of airborne particles, including dust, mist, and fumes.

In addition to its robust filtration, the 3M S10 utilizes Smart Sensor technology. This feature monitors the user’s environment and adjusts the airflow accordingly, providing a continuous supply of clean air even in fluctuating conditions. The smart sensor also enhances battery life by optimizing energy consumption, allowing for prolonged use in the field.

The S10 is designed with user comfort in mind. Its lightweight construction and adjustable head straps ensure a secure yet comfortable fit for extended wear. The device features a low-profile design that does not obstruct peripheral vision, making it suitable for tasks that require precision and attention to detail. Additionally, the interchangeable facepiece sizes accommodate various facial shapes, promoting a better seal and reducing the risk of leakage.

Another key characteristic of the 3M S10 is its user-friendly interface. The integrated digital display provides real-time feedback on battery life, filter status, and airflow levels, enabling users to monitor their equipment status easily. This feature reduces downtime by ensuring that workers can quickly identify when maintenance is necessary.

Lastly, the durable construction of the S10 ensures it can withstand harsh working environments. It is made from robust materials that resist wear and tear, making it suitable for industries such as construction, manufacturing, and chemical processing. Overall, the 3M S10 is a versatile and reliable safety device that effectively combines advanced technology with practical features, safeguarding workers while enhancing their operational efficiency.
Top Page Image Contents