3M S10 manual Lamp

Page 32

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken

If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

Use the lamp of the specified type only. See the section “ACCESSORIES”.

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.

32

Image 32
Contents S10 Multimedia Projector Contents Projector Features PreparationPart Names ProjectorAttaching The Base Slowly turn the projector so that the top is facing upTo adjust the keystone ProjectorRemote Control Setting Up ArrangementAdjusting The Projectors Elevator Adjust the height of the projector byAs necessary, you can also finely Twisting the elevator feet by handConnecting Your Devices Connecting to a computer AUDIO-L AUDIO-R G B RConnecting Power Supply Remote Control Remove Battery coverClose Battery cover Putting BatteriesOperating The Remote Control Power ON/OFF Turning On The PowerMake sure that the power cord is Remote controlSelecting An Input Signal Selecting a RGB signalUse the zoom ring to adjust the screen Size Use the focus ring to focus the pictureTurning Off The Power Switch the power switch to O OFFTemporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Using The Automatic Adjustment Feature Correcting Keystone DistortionsUsing The Magnify Feature Use Buttons to adjust the zoom LevelFreezing The Screen Press the Magnify on buttonTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Multifunctional Settings Using The Menu FunctionsMain Menu Picture 1 Menu Load/Save a Setting Reset the PICTURE-1 Menu ItemsPicture 1 Menu LOAD4Phase Picture 2 MenuPosition SizeInput Menu Color SpaceVideo Frame LockInput Menu Video NRInformation S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Volume Option MenuScreen Type Lamp TimeLamp Replacing The Lamp Caring For The Air Filter Reset the filter timerAir Filter Replacing The Air Filter Hold the release buttons of the airFilter, while pulling down it Filter coverCaring For The Cabinet And Remote Control Other CareCaring For The Inside Of The Projector Caring For The LensTroubleshooting Related MessagesRelated Messages Regarding The Indicator Lamps Power Lamp Temp DescriptionRegarding The Indicator Lamps IndicatorPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Specifications SpecificationRGB Input Ports Audio Ports Video Input PortsAccessories Accessories ……………………………………………………… Part NumberHow to Order Not Included with Basic Packet ………………………………… Part NumberDN00571 S10OGENG

S10 specifications

The 3M S10 is a state-of-the-art personal safety device designed to enhance worker safety across various industrial settings. This innovative product seamlessly combines advanced technology with ergonomic design to provide users with reliable protection and comfort during their daily tasks.

One of the standout features of the 3M S10 is its advanced respiratory protection capabilities. It employs a powerful filtration system that effectively captures airborne particles, gases, and vapors, ensuring that workers are shielded from harmful contaminants. The S10 is equipped with a P100 filter that offers a high level of filtration efficiency, capturing at least 99.97% of airborne particles, including dust, mist, and fumes.

In addition to its robust filtration, the 3M S10 utilizes Smart Sensor technology. This feature monitors the user’s environment and adjusts the airflow accordingly, providing a continuous supply of clean air even in fluctuating conditions. The smart sensor also enhances battery life by optimizing energy consumption, allowing for prolonged use in the field.

The S10 is designed with user comfort in mind. Its lightweight construction and adjustable head straps ensure a secure yet comfortable fit for extended wear. The device features a low-profile design that does not obstruct peripheral vision, making it suitable for tasks that require precision and attention to detail. Additionally, the interchangeable facepiece sizes accommodate various facial shapes, promoting a better seal and reducing the risk of leakage.

Another key characteristic of the 3M S10 is its user-friendly interface. The integrated digital display provides real-time feedback on battery life, filter status, and airflow levels, enabling users to monitor their equipment status easily. This feature reduces downtime by ensuring that workers can quickly identify when maintenance is necessary.

Lastly, the durable construction of the S10 ensures it can withstand harsh working environments. It is made from robust materials that resist wear and tear, making it suitable for industries such as construction, manufacturing, and chemical processing. Overall, the 3M S10 is a versatile and reliable safety device that effectively combines advanced technology with practical features, safeguarding workers while enhancing their operational efficiency.