Zone 2
■There’s no sound
Audio can be output only when analog, NET or USB input source is selected in Zone 2.
Music Server and Internet Radio
■Can’t access the server or Internet radio
Certain network service or contents available through this device may not be accessible in case the service provider terminates its service.
Check the network connection between the AV receiver and your router or switch. (➔ page 15)
Make sure that your modem and router are properly connected, and make sure they are both turned on.
Make sure the server is up and running and compatible with the AV receiver. (➔ page 72)
Check the “11. Network Setup”. (➔ page 54)
■Playback stops while listening to music files on the server
Make sure your server is compatible with the AV receiver. (➔ page 72)
If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server.
If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted. Reduce the number of playback devices on the network, upgrade your network, or use a switch instead of a hub.
■Can’t connect to the AV receiver from a Web browser
If you’re using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you can’t connect to a server or Internet radio station, recheck the AV receiver’s IP address on the “Network Setup” screen. (➔ page 54)
Check the “11. Network Setup”. (➔ page 54)
USB Device Playback
■Can’t access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.
(➔ page 72)
Depending on the type of format, the playback from a USB device may not be performed normally. Check the type of the file formats that is supported. (➔ page 73)
USB memory devices with security functions cannot be played.
Others
■Standby power consumption
In the following cases, the power consumption in standby mode may reach up to a maximum of 5 W:
–The “HDMI CEC (RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.)
–The “HDMI Through” setting is set to other than “Off”.
–The “Network Standby” setting is set to “On”.
(➔ pages 52, 53, 55)
■The sound changes when I connect my headphones
When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio (European, Australian and Asian models).
■The speaker distance cannot be set as required
The values entered may be automatically adjusted with values
■The display doesn’t work
The display is turned off when the Pure Audio (European, Australian and Asian models) listening mode is selected.
Appendix
■How do I change the language of a multiplex source
Use the “Input Ch (Mux)” setting in the “Audio Adjust” menu to select “Main” or “Sub”. (➔ page 48)
■The ufunctions don’t work
To use u, you must make an uconnection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. (➔ page 19)
While Zone 2 is selected, the ufunctions don’t work. (➔ page 19)
■The functions System On/Auto Power On and Direct Change don’t work for components
connected via u
These functions don’t work when Zone 2 is turned on.
(➔ page 19)
■When performing Automatic Speaker Setup, the measurement fails and the message “Ambient noise is too high.” is displayed.
This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds.
■The following settings can be made for the composite video inputs
You must use the buttons on the unit to make these settings.
On the AV receiver, press the input selector for the input source that you want to set and the HOME button simultaneously. While holding down the input selector button, press HOME until “Video ATT :On” appears on the AV receiver’s display. Then, release both buttons. To turn the setting off, repeat the above process so that “Video ATT :Off” appears on the AV receiver’s display, and release the buttons.