Mitsubishi Electronics WD390U-EST Installing the virtual display driver, Using remote desktop

Page 47

Advanced display utilities (continued)

•About

Displays the version information of the LAN Display System.

•Exit

Exits the LAN Display System.

Important:

•The items marked with “*” are not available for

Mac OS X.

•When “Advanced Screen Capture” is enabled, the computer mouse cursor may blink.

Ending the LAN Display projection

5.Click the Exit button on the main user interface or the menu window to exit the LAN Display System.

6.In case of the wireless LAN communication, unplug the USB wireless LAN adapter from the projector. Before unplugging, be sure to press the UNPLUG button on the remote control and select [Yes] on the screen by pressing the or button and then ENTER button.

Important:

•Do not switch the input source to USB Display or PC Less Presentation during the wireless LAN communication. If switched, the communication will be disconnected.

•During wireless LAN communication, the projector cannot communicate with the access point.

•Only infrastructure mode is available to wireless

LAN communication. Adhoc mode is not available.

Installing the virtual display driver

To project a virtual extended screen, install the Virtual display driver as follows.

1.Double-click “Virtual display driver.exe” contained in “C:¥Program Files¥LAN Display System”, and start up the installer of the Virtual display driver.

2.The Setup window is displayed. Click [Next] and operate according to the instructions on the window.

3.When the installation has been completed, restart the computer.

Using remote desktop

Connect an USB device such as a mouse or keyboard to the USB-A terminal on the projector. While the computer images are projected with the LAN Display, the computer can be operated with the device.

AUDIO

AUDIO IN-3L S-VIDEO

SERIAL

COMPUTER / COMPONENT VIDEO

USB-B

USB-A

LAN

IN-1

 

 

 

 

 

AUDIO OUT

 

 

IN-1

 

 

 

AUDIO

 

 

 

 

 

 

IN-2

AUDIO IN-3R

 

IN-2

 

 

 

 

VIDEO

MONITOR OUT

 

 

 

To USB-A terminal

Important:

•The USB-A terminal on this projector is compatible with USB 2.0.

•Supported USB device is standard USB HID device with power consumption less than 5V/500mA.

•When using a keyboard and mouse together, we recommend a commercially available wireless keyboard and wireless mouse intended for a computer with wireless receiver.

•When using a USB hub, you are recommended to use the one with external power supply.

•Some USB hubs cannot be used depending on the specifications.

EN-47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents WD390U-EST Risk of Electric Shock Do not Open Contents Important safeguards Do not block the intake and exhaust vents Important safeguardsNever remove the cabinet Do not modify this equipment Use correct voltageTerminal panel OverviewControl panel Overview Bottom side Remote controlInserting the batteries into the remote control Remote controlBattery installation Operation range of the remote controlWhen the aspect ratio of the image is InstallationWhen the aspect ratio of the screen is When the aspect ratio of the image is 1610 WxgaRear projection InstallationCeiling mount installation Front projection, ceiling mountingProjector + DVD player or Hdtv decoder Basic connectionsProjector + AV device Connection for video equipment having an Hdmi terminal Basic connectionsFor computer with Mini D-SUB Projector + ComputerPreparation Adjustment of the projection angleWhen projected images are distorted to a trapezoid Using the adjustment feet frontPreparation Basic operation Power-onStatus Power Basic operation With the remote control Setting the aspect ratioWatching 3D content When connecting to a laptop computerEN-19 Menu operation You can make various settings using the displayed menusMain Menu How to set the menusInstallation Menu operationPicture Setting FunctionMenu items Picture menuVideo Image Video Image menuLPF Signal menuSignal RGBAudio Audio menuLAN Installation menuOption Option menuWxga Ssid Network Config menuSET DhcpInformation Information menuDescription To adjust the tone of white Color Temp Image adjustmentTo adjust the brightness Contrast and Brightness To adjust the color Color and TintGamma Image adjustmentImage Color ManagementTo adjust the vertical position How to adjust the computer imageSimple method to adjust the image position To adjust the horizontal positionEnabling or disabling the network certification Network settingsSetting Projector Name Network Password settingsIP Address settings Network settingsIP Config settings Setting or clearing DhcpStart IP Address setting Subnet Mask settingsDefault Gateway settings Setting or clearing Dhcp FunctionSsid setting Wireless SettingChannel setting Encryption settingEnabling or disabling the AMX Device Discovery Initialization of network settingsWireless Setup setting How to use network functionCreating a user account Important Preparation for using Remote DesktopAdvanced display utilities Thin client In Windows Vista Advanced display utilities In Windows XP Operation Installation of softwareConnection To disconnect with ending the session Connecting the projector to the computerClient Access License CAL USB Display Installation of driverInstalling USB Display driver When deleting USB Display driver Uninstallation Starting USB Display projection  When using Mac OS Installing LAN Display System LAN DisplayProjection When deleting LAN Display System Uninstallation ImportantSplit 1-4 buttons Starting the LAN Display SystemOperating the LAN Display System Play buttonExit Installing the virtual display driverUsing remote desktop AboutStarting SidePad Using SidePad functionInstallation of software ConnectionPC Less Presentation Installation of PtG Converter-LiteOFF Setting upPerforming the PC Less Presentation Selecting a PC Less Presentation inputDisplaying with slideshow function Displaying PtG fileDisplaying Jpeg file Displaying with AutoRun functionStarting WiFi-Doc  When using iOS WiFi-DocWireless network setting on the tablet computer Ending WiFi-Doc  When using AndroidMagnify Advanced featuresDisplaying a user-defined image during startup or muting FreezeTo set a password Advanced featuresPassword lock To enable or disable password lockMajor functions PJLink supported commands When the projector is mounted to the ceiling Lamp replacementWhen the projector is placed on the table Interval of lamp replacement Lamp replacementReset of the lamp operation time No image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution EN-63 Kensington Lock MaintenanceCleaning of the projector and the vents Cleaning of the lensNormal condition IndicatorsPower Status Condition Power Status Condition Possible SolutionYPBPR/YCBCR SpecificationsWD390U-EST Replacement part option/not included in the box SpecificationsConnectors Dimension drawings unit mmXGA85 Supported input signalsZusho Baba, Nagaokakyo-City, Kyoto Japan
Top Page Image Contents