Mitsubishi Electronics XD560U Restart of network function, Initialization of network settings

Page 37

Network settings (continued)

•The number of characters of KEY varies depending on the Encryption setting.

•WEP 128bit(ASCII): 13 chars

•WEP 64bit(ASCII): 5 chars

•WEP 128bit(HEX): 26 digits

•WEP 64bit(HEX): 10 digits

•WPA-PSK(ASCII): 8-63 chars

•WPA2-PSK(ASCII): 8-63 chars

•WPA-PSK(HEX): 64 digits

•WPA2-PSK(HEX): 64 digits

•If the entered content is outside character number range, the KEY screen appears again after an error dialog is displayed.

Restart of network function

(See page 21 for menu setting.)

1.Display the Network Config menu.

2.Press the or button to select Network Restart.

Network Restart

OK

 

 

 

 

 

 

 

3.Press the ENTER button.

•Network Restart dialog appears.

4.If the ENTER button is pressed again, the network function will be restarted.

•It may take some time to restart the function.

Wireless Setup setting

1.Display the Wireless Setting menu.

2.Press the or button to select Wireless Setup.

Wireless Setup

OK

 

 

 

 

 

 

 

3.Press the ENTER button.

•Confirmation dialog appears.

4.If the ENTER button is pressed again, the Wireless Setting will be reflected.

•It may take some time to reflect the setting.

Enabling or disabling the AMX Device Discovery

Select this setting when using the AMX controller. (See page 21 for menu setting.)

1.Display the Network Config menu.

2.Press the or button to select AMX Device Discovery.

AMX Device Discovery

Off

 

 

 

 

 

 

 

3.Press the ENTER button.

• AMX dialog appears.

AMX : OFF

OK : ENTER CANCEL : MENU

4.Press the or button to select ON or OFF .

5.Select the item to set, and press the ENTER button.

•To cancel the setting, press the MENU button.

•It may take some time to reflect the setting.

Initialization of network settings

(See page 21 for menu setting.)

1.Display the Network Config menu.

2.Press the or button to select Network Initialization.

Network Initialization

OK

 

 

 

 

 

 

 

3.Press the ENTER button.

•Network Initialization dialog appears.

4.If the ENTER button is pressed again, the network settings will be initialized.

•It may take some time to initialize the settings.

How to use network function

•When connecting a computer and projector with

LAN, configure the both IP Addresses in the same network group.

If connecting in different network group, be sure to use a router. As for the settings of a router, ask the network administrator.

•Configure the IP Config correctly. If the settings are not correct, the communication may be unavailable. For the detail, consult the network administrator.

•Depending on the settings of Standby Mode of the projector, LAN function may be unavailable. See page 26 for the detail of Standby Mode.

Glossary

For more detail of the glossary below, refer to the technical book that is commercially available.

Term

Description

 

 

 

Abbreviation for Dynamic Host

DHCP

Configuration Protocol. This

protocol automatically assigns IP

 

 

Address to networked devices.

 

 

IP Address

Numerical address to identify

networked computers.

 

 

 

 

A numeric value to define the

Subnet Mask

number of bits used for a network

address of a divided network (or

 

 

subnet) in an IP Address.

 

 

 

A server (or router) to communicate

Default Gateway

across networks (subnets) that are

 

divided by Subnet Mask.

 

 

 

Abbreviation for Media Access

 

Control Address. MAC Address is a

MAC Address

unique ID number assigned to each

network adapter. And this is based

 

 

on which data are sent and received

 

between network adapters.

 

 

EN-37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents XD550U XD560U WD570U Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Overview Power button ON/STANDBYControl panel Terminal panelOverview Bottom side Remote controlBattery installation Remote controlOperation range of the remote control Inserting the batteries into the remote controlLayout of XD550U/XD560U InstallationLayout of WD570U When the aspect ratio of the screen is InstallationWhen the aspect ratio of the image is 1610 Wxga When the aspect ratio of the image isFront projection, ceiling mounting Ceiling mount installationRear projection Projector + AV device Basic connectionsProjector + DVD player or Hdtv decoder Connection for video equipment having an Hdmi terminal Basic connectionsFor computer with Mini D-SUB Projector + ComputerUsing the adjustment feet front Adjustment of the projection anglePreparation Preparation for projectionStatus Power Power-onBasic operation ConditionBasic operation When connecting to a laptop computer Watching 3D content Setting the aspect ratioWith the remote control With the Picture menuEN-19 Menu operation You can make various settings using the displayed menusMenu operation How to set the menusPicture menu Menu itemsVideo Image Video Image menuSignal Signal menuRGB LPFAudio Audio menuLAN Installation menuWxga Option menuOption SET Network Config menuDhcp SsidDescription Information menuInformation To adjust the brightness Contrast and Brightness Image adjustmentTo adjust the color Color and Tint To adjust the tone of white Color TempImage Image adjustmentColor Management GammaSimple method to adjust the image position How to adjust the computer imageTo adjust the horizontal position To adjust the vertical positionSetting Projector Name Network settingsNetwork Password settings Enabling or disabling the network certificationIP Config settings Network settingsSetting or clearing Dhcp IP Address settingsDefault Gateway settings Subnet Mask settingsSetting or clearing Dhcp Function Start IP Address settingSsid setting Channel setting Wireless SettingEncryption setting Press the Enter button Wireless Setting menu appearsWireless Setup setting Initialization of network settingsHow to use network function Restart of network functionUSB Display Advanced display utilitiesConnection OperationInstalling LAN Display System Installation of softwareWhen deleting LAN Display System Uninstallation Important Advanced display utilitiesProjection Installing the virtual display driver Using remote desktopHide UI AboutPC Less Presentation Installation of PtG Converter-LiteClick the PtG Converter-Lite icon to execute the program Performing the PC Less PresentationConnect a USB device to the USB-A terminal on the projector Selecting a PC Less Presentation inputOFF Setting upDisplaying PtG file Displaying Jpeg fileDisplaying with slideshow function Displaying with AutoRun functionEnding the PC Less Presentation Displaying a user-defined image during startup or muting Advanced featuresFreeze MagnifyPassword lock Advanced featuresTo enable or disable password lock To set a passwordMajor functions PJLink supported commands When the projector is placed on the table Lamp replacementWhen the projector is mounted to the ceiling Reset of the lamp operation time Lamp replacementInterval of lamp replacement No image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens Kensington LockPower Status Condition IndicatorsPower Status Condition Possible Solution Normal conditionYPBPR/YCBCR SpecificationsConnectors SpecificationsDimension drawings unit mm Replacement part option/not included in the boxEN-59 Ver
Top Page Image Contents